TLV4113IN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | TLV4113 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 700μA |
| Nominal Supply Current | 2mA |
| Power Dissipation | 1.6W |
| Output Current | 320mA |
| Slew Rate | 1.57V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 0.3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~6V |
| Output Current per Channel | 320mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 2.7MHz |
| Unity Gain BW-Nom | 2700 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 175μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 3.5mV |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV4113IN Overview
In the package, you will find a 14-DIP (0.300, 7.62mm)-case to contain the op amp ic. A General Purpose-type buffer amplifier is shown here. A Tube case is used for delivering the op amp. We are approaching the 14h termination of the year. There are a total of 14 pins on this op amp. As a reminder, this buffer op amp should be powered by 3V battery and that the battery should be inserted in the amplifier. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 14 pins on it. There is an input offset voltage of 3.5mV for this buffer op amp. The mounting type that is recommended for this electrical part is Through Hole. With regard to operating temperature, op amp ranges -40°C~125°C. Operational amplifier can operate supply current at 700μA. Op amp is a member of the 110dB's 110dB family. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. There are a total of 2 elements in this linear amplifier.
TLV4113IN Features
14 Pins
supply voltage of 3V
110dB voltage gain
Output Type: Rail-to-Rail
TLV4113IN Applications
There are a lot of Texas Instruments TLV4113IN Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Oscilloscopes
- Fission chambers
- Power generator
- Video conversion and routing
- Test and measurement instruments
- Signal operation
- Polarized electrodes
- Band-pass filter
- Exponential operation circuits
