TPS2010DRG4
| Parameters | |
|---|---|
| Quiescent Current | 73μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Min Current Limit | 220mA |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Rds On (Typ) | 75m Ω |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | NRND (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 75mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TPS2010 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 200mA |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Nominal Supply Current | 73μA |
| Output Configuration | High Side |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 73μA |
| Adjustable Threshold | NO |
TPS2010DRG4 Overview
Tape & Reel (TR) is how it's packaged.There is a 8-SOIC (0.154, 3.90mm Width) package that includes it.Surface Mount is the mounting type of the LED driver.There is a switch type of General Purpose.It is recommended that the temperature be set to -40°C~125°C TJ for reliable operation.The lighting driver has a total of 1 outputs that are available for use.It uses a supply voltage of Not Required to operate.Voltage output is N-Channel volts at maximum.There is a TPS2010 family of things that it belongs to.It contains 8 terminations.The 8 pins are used to operate the LED driver.As far as the lighting driver is concerned, there are 1 functions.As a result, the maximum output current is reduced to 200mA in order to meet the operation requirements.A supply voltage of 3V leads to high efficiency.As a result, it has a total of 8 pins.In this case, there is 75mOhm resistance in the LED driving board.In this case, the output current is set to 200mA.This LED driving board uses an analog IC POWER SUPPLY SUPPORT CIRCUIT.There are a total of 1 channels to choose from.In order to achieve the best efficiency, the supply voltage should be set to 5.5V.The maximum input voltage of the LED driver is 5.5V volts.As far as input voltage goes, it has a minimum of 2.7V volts.This system has a maximum current requirement of 73μA.
TPS2010DRG4 Features
Supplied from 3V
Resistance of 75mOhm
1 channels
TPS2010DRG4 Applications
There are a lot of Texas Instruments TPS2010DRG4 Power Switches ICs applications.
- Various applications equipped with buttons
- Storage Drives
- Storage (HDDs, SSDs)
- Low Voltage I/O System Power
- Mobile Communication Devices
- Hot Swaps
- Set-Top Boxes
- Gaming
- Hot-Swap Systems
- PC Card Hot Swap
