TPS2012ADG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 30mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | TPS2012 |
| Pin Count | 8 |
| Output Type | N-Channel |
| Max Output Current | 1A |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Nominal Supply Current | 73μA |
| Output Configuration | High Side |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 73μA |
| Adjustable Threshold | NO |
| Quiescent Current | 73μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Number of Inputs | 1 |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Min Current Limit | 1.1A |
| Fault Protection | Current Limiting (Fixed), Over Temperature, UVLO |
| Rds On (Typ) | 33m Ω |
| Height | 1.58mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS2012ADG4 Overview
It is packaged in the manner of a Tube.It is included with the 8-SOIC (0.154, 3.90mm Width) package as well.A Surface Mount mounting is used for the LED driving board.General Purpose is the switch type that it owns.It is recommended to set the temperature to -40°C~125°C TJ in order to ensure reliable operation.A voltage of Not Required is used to power it.The maximum output voltage of this LED driver is N-Channel volts.As you can see, it comes from the TPS2012 family.It contains 8 terminations.It is necessary to use the 8 pins in order to operate the LED driver.As far as functions are concerned, the lighting driver has 1.This results in the maximum output current dropping to 1A to meet the operation criteria.The supply voltage of 3.3V is conducive to high efficiency.8 pins are equipped with it.30mOhm resistance is present in the lighting driver.As a result, the output current is set to 1A.The analog IC used in this lighting driver is POWER SUPPLY SUPPORT CIRCUIT.The total number of channels is 1.For maximum efficiency, the supply voltage should be set to 5.5V.As far as input voltage goes, its maximum is 5.5V volts.It has a 2.7V volt minimum input voltage.For its operation, a maximum current requirement of 73μA is required.Currently, there are 1 inputs available.
TPS2012ADG4 Features
Supplied from 3.3V
Resistance of 30mOhm
1 channels
TPS2012ADG4 Applications
There are a lot of Texas Instruments TPS2012ADG4 Power Switches ICs applications.
- Hard Disk Drives
- Low Voltage I/O System Power
- Smart Phones, Feature Phones
- Portable GPS
- Hot Swap
- Solid-State Drives
- Wireless/Networking Cards
- USB Power Distribution
- Wireless Modem Data Cards
- HDD, SSD
