TPS2013PWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | TPS2013 |
| Pin Count | 14 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Current - Output (Max) | 1.5A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Adjustable Threshold | NO |
| Quiescent Current | 73μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Rds On (Typ) | 75m Ω |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS2013PWRG4 Overview
The LED driver's packaged as a Tape & Reel (TR).There is a package for it in the 14-TSSOP (0.173, 4.40mm Width) package.A Surface Mount mounting is used for the LED driving board.General Purpose is the switch type it owns.Keeping the temperature at -40°C~125°C TJ ensures reliable operation.In this LED driver, there are no outputs available.Operation is based on a supply voltage of Not Required.A maximum output voltage of N-Channel volts has been specified.As you can see, it comes from the TPS2013 family.The termination count is 14.In order to operate, 14 pins are used.As far as functions are concerned, the lighting driver has 1.This lighting driver is capable of delivering a maximum output of 1.5A volts.Supply voltages of 3V allow for high efficiency.Surface Mount is mounted in the way of this lighting driver.In total, it has 14 pins.There is an analog input IC in this gadget, which is POWER SUPPLY SUPPORT CIRCUIT.To choose from, there are 1 channels.In order to optimize the efficiency of the supply voltage, it should be set to 5.5V.Voltage input is limited to 5.5V volts.There is a minimum input voltage of 2.7V volts for this LED driver.
TPS2013PWRG4 Features
Supplied from 3V
1 channels
TPS2013PWRG4 Applications
There are a lot of Texas Instruments TPS2013PWRG4 Power Switches ICs applications.
- Hard Disk Drives
- Telecom and Network Systems
- Various applications equipped with buttons
- Gaming
- Notebook PC
- PC Card Hot Swap
- USB Power Distribution
- USB Protection
- Hot Swap
- Portable/Handheld Devices
