TPS2080DG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | 0°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 80mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Peripheral Drivers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3.3V |
| Base Part Number | TPS2080 |
| Pin Count | 8 |
| Output Type | N-Channel |
| Max Output Current | 500mA |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Interface | On/Off |
| Nominal Supply Current | 85μA |
| Output Configuration | High Side |
| Output Current | 500mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 85μA |
| Quiescent Current | 85μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Number of Inputs | 2 |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 2 |
| Min Current Limit | 700mA |
| Fault Protection | Current Limiting (Fixed), Over Temperature, UVLO |
| Output Peak Current Limit-Nom | 1A |
| Rds On (Typ) | 80m Ω |
| Turn Off Time | 40000 µs |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS2080DG4 Overview
As you can see, it's packaged in the way of a Tube.The 8-SOIC (0.154, 3.90mm Width) package contains it.The lighting driver has the mounting type Surface Mount.The switch type is General Purpose.It is recommended to set the temperature to 0°C~125°C TJ in order to ensure reliable operation.The LED driving board operates at Not Required volts.A maximum output voltage of N-Channel volts can be achieved by this LED driver.It is equipped with Status Flag features.It belongs to the TPS2080 family.It has a total of 8 terminations.It is necessary to use the 8 pins in order to operate the LED driver.It consists of 2 functions.To comply with the operation criteria, the maximum output current is reduced to 500mA.High efficiency is possible at 3.3V supply voltage.The LED driving board is equipped with a total of 8 pins.Lighting drivers with 80mOhm resistance are used.When this case is used, the output current is set to 500mA.The LED driver is packaged in an econtainer with a capacity of Peripheral Drivers.In this part, the power supply is set to 3/5V.In order to optimize the efficiency of the supply voltage, it should be set to 5.5V.This LED driver can handle voltages up to 5.5V volts.A voltage of 2.7V volts is the minimum input voltage.For its operation, a maximum current requirement of 85μA is required.2 inputs are available.
TPS2080DG4 Features
Supplied from 3.3V
Resistance of 80mOhm
TPS2080DG4 Applications
There are a lot of Texas Instruments TPS2080DG4 Power Switches ICs applications.
- Hard Disk Drives
- Notebook and Tablet Computers
- Portable GPS Device
- Hot-Swap Systems
- Smart Phones, Feature Phones
- Portable/Handheld Devices
- Solid State Drivers
- Gaming
- PDAs
- USB Power Distribution
