TPS22913BYZVR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Copper, Silver, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 4-XFBGA, DSBGA |
| Number of Pins | 4 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Feature | Load Discharge, Slew Rate Controlled |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Resistance | 84mOhm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Peripheral Drivers |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.5V |
| Terminal Pitch | 0.5mm |
| Current Rating | 30A |
| Base Part Number | TPS22913 |
| Pin Count | 4 |
| Voltage - Rated AC | 240V |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Operating Supply Voltage | 5.5V |
| Interface | On/Off |
| Output Configuration | High Side |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Number of Poles | 3 |
| Quiescent Current | 2μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 234 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 1.4V |
| Max Input Voltage | 5.5V |
| Output Characteristics | OPEN-DRAIN |
| Turn-Off Delay Time | 17 μs |
| Ratio - Input:Output | 1:1 |
| Input Characteristics | STANDARD |
| Voltage - Load | 1.4V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Reverse Current, UVLO |
| Rds On (Typ) | 60m Ω |
| Built-in Protections | TRANSIENT; UNDER VOLTAGE |
| Height | 500μm |
| Length | 0m |
| Width | 0m |
| Thickness | 350μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS22913BYZVR Overview
As a result, it is packaged in the form of a Tape & Reel (TR).Package 4-XFBGA, DSBGA contains it.The lighting driver has the mounting type Surface Mount.The switch type of this switch is General Purpose.It is best to set the temperature to -40°C~85°C TA to ensure reliable operation.It is possible to use 1 outputs in the lighting driver.The LED driving board is powered by a voltage of Not Required.The maximum output voltage of this LED driver is P-Channel volts.It has a total of Load Discharge, Slew Rate Controlled features.The TPS22913 family contains this object.It contains 4 terminations.The operation is carried out using the 4 pins.It contains 1 functions.A supply voltage of 1.5V leads to high efficiency.It is mounted in the way of Surface Mount.4 pins are equipped with it.In this LED driving board, there is 84mOhm resistance.This results in a 2A output current.This LED driver is self-contained in an econtainer with a capacity of Peripheral Drivers.When using this LED driving board, it is recommended that the supply voltage is set to 5.5V.Voltage input is limited to 5.5V volts.The minimum input voltage is 1.4V volts.
TPS22913BYZVR Features
Supplied from 1.5V
Resistance of 84mOhm
TPS22913BYZVR Applications
There are a lot of Texas Instruments TPS22913BYZVR Power Switches ICs applications.
- Notebook and Tablet Computers
- Hot-Swap Systems
- Set-Top Boxes
- PC Card Hot Swap
- Portable Devices
- PDAs
- Mobile Communication Devices
- PC Cards
- Solid State Drivers
- Hot Swap
