banner_page

TPS22913CYZVR

P-Channel 0.5mm Copper, Silver, Tin PMIC TPS22913 4 Pin 1.5V 4-XFBGA, DSBGA


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-TPS22913CYZVR
  • Package: 4-XFBGA, DSBGA
  • Datasheet: -
  • Stock: 282
  • Description: P-Channel 0.5mm Copper, Silver, Tin PMIC TPS22913 4 Pin 1.5V 4-XFBGA, DSBGA (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 4 days ago)
Contact Plating Copper, Silver, Tin
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 4-XFBGA, DSBGA
Number of Pins 4
Operating Temperature -40°C~85°C TA
Packaging Cut Tape (CT)
JESD-609 Code e1
Feature Load Discharge, Slew Rate Controlled
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 4
ECCN Code EAR99
Resistance 80mOhm
Terminal Finish Tin/Silver/Copper (Sn/Ag/Cu)
Subcategory Peripheral Drivers
Terminal Position BOTTOM
Terminal Form BALL
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 1.5V
Terminal Pitch 0.5mm
Base Part Number TPS22913
Pin Count 4
Number of Outputs 1
Output Type P-Channel
Max Output Current 2A
Operating Supply Voltage 5.5V
Interface On/Off
Output Configuration High Side
Output Current 2A
Voltage - Supply (Vcc/Vdd) Not Required
Quiescent Current 2μA
Input Type Non-Inverting
Turn On Delay Time 770 μs
Switch Type General Purpose
Min Input Voltage 1.4V
Max Input Voltage 5.5V
Output Characteristics OPEN-DRAIN
Nominal Input Voltage 5.5V
Turn-Off Delay Time 6.6 μs
Ratio - Input:Output 1:1
Input Characteristics STANDARD
Voltage - Load 1.4V~5.5V
Driver Number of Bits 1
Fault Protection Reverse Current, UVLO
Rds On (Typ) 60m Ω
Built-in Protections TRANSIENT; UNDER VOLTAGE
Height 500μm
Length 0m
Width 0m
Thickness 350μm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

TPS22913CYZVR Overview


As a result, it is packaged in the form of a Cut Tape (CT).In the 4-XFBGA, DSBGA package, it is included.The lighting driver has the mounting type Surface Mount.The switch type is General Purpose.It is recommended that the temperature be set to -40°C~85°C TA for reliable performance.In this LED driver, there are no outputs available.In order to operate, it requires a voltage supply of Not Required.A maximum output voltage of P-Channel volts can be achieved by this LED driver.It has a total of Load Discharge, Slew Rate Controlled features.It comes under the family of TPS22913.It contains 4 terminations.It is necessary to use the 4 pins in order to operate the LED driver.It has 1 functions.The maximum output current is reduced to 2A to meet the operation criteria.With a supply voltage of 1.5V, high efficiency is possible.As a result, it is mounted in the manner of Surface Mount.There are 4 pins in total on this board.There is 80mOhm resistance on the LED driver.This results in a 2A output current.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.It is recommended to set the supply voltage to 5.5V for optimum efficiency.Voltage input is limited to 5.5V volts.The minimum input voltage is 1.4V volts.

TPS22913CYZVR Features


Supplied from 1.5V
Resistance of 80mOhm

TPS22913CYZVR Applications


There are a lot of Texas Instruments TPS22913CYZVR Power Switches ICs applications.

  • Portable Video Game Players
  • Low Voltage I/O System Power
  • Mobile Communication Devices
  • Hard Disk Drives
  • Handheld Devices
  • PDAs
  • PC Card Hot Swap
  • USB Power Distribution
  • Hot Swap
  • USB Power Distribution

Write a review

Note: HTML is not translated!
    Bad           Good