TPS22921YZPR
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Feature | Slew Rate Controlled |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Type | General Purpose |
| Resistance | 116mOhm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Max Power Dissipation | 645mW |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS22921 |
| Pin Count | 6 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 2A |
| Operating Supply Voltage | 3.6V |
| Supply Voltage-Min (Vsup) | 0.9V |
| Number of Channels | 1 |
| Interface | On/Off |
| Nominal Supply Current | 120nA |
| Output Configuration | High Side |
| Power Dissipation | 645mW |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 120nA |
| Adjustable Threshold | NO |
| Quiescent Current | 200nA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 188 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 750mV |
| Max Input Voltage | 3.6V |
| Turn-Off Delay Time | 975 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 0.9V~3.6V |
| Rds On (Typ) | 14m Ω |
| Height | 500μm |
| Length | 1.5mm |
| Width | 900μm |
| Thickness | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 6-XFBGA, DSBGA |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
TPS22921YZPR Overview
It is packaged in the form of a Tape & Reel (TR).It's included in the 6-XFBGA, DSBGA package.It has been mounted as Surface Mount on the LED driver.General Purpose is the switch type it owns.It is recommended that the temperature be set to -40°C~85°C TA for reliable operation.The LED driver is equipped with 1 outputs.A supply voltage of Not Required is required for it to operate.There is a maximum output voltage of P-Channel volts.As far as features are concerned, the LED driving board has Slew Rate Controlled.It belongs to the family TPS22921.It has a total of 6 terminations.For operation, we use the 6 pins.The LED driver has 1 functions.The maximum output current must drop to 2A to meet the operation criteria.The supply voltage of 1V is conducive to high efficiency.6 pins are connected to it in total.In this case, there is 116mOhm resistance in the LED driving board.As a result, the output current is set to 2A.In order to operate normally, the supply voltage (Vsup) must be maintained above 0.9V.In total, there are 1 channels available.The supply voltage should be set at 3.6V for best efficiency.The maximum input voltage is 3.6V volts.The minimum input voltage is 750mV volts.For its operation, a maximum current requirement of 120nA is required.The electrical component has the classification General Purpose.
TPS22921YZPR Features
Supplied from 1V
Resistance of 116mOhm
1 channels
TPS22921YZPR Applications
There are a lot of Texas Instruments TPS22921YZPR Power Switches ICs applications.
- Hot Swap
- USB Power Distribution
- Mobile Communication Devices
- USB3.1 Power Delivery
- USB Ports/Hubs
- Wireless Modem Data Cards
- Portable GPS
- Wireless/Networking Cards
- Solid-State Drives
- Gaming
