TPS2301IPWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Feature | Latched Fault, UVLO |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | Hot Swap Controller |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Applications | General Purpose |
| Subcategory | Power Management Circuits |
| Voltage - Supply | 3V~13V 3V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TPS2301 |
| Pin Count | 20 |
| Output Voltage | 21V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Channels | 2 |
| Nominal Supply Current | 200μA |
| Adjustable Threshold | YES |
| Current - Supply | 5μA |
| Nominal Input Voltage | 13V |
| Internal Switch(s) | No |
| Programmable Features | Circuit Breaker, Fault Timeout, Slew Rate |
| Feature Pins | DISCH1, DISCH2, ENABLE, /FAULT, ISET1, ISET2, PWRGD1, PWRGD2, TIMER, VREG |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS2301IPWRG4 Overview
You get it with the 20-TSSOP (0.173, 4.40mm Width) package.Hot-swappable device is currently possible to access 2 channels.There is a Tape & Reel (TR)-shaped package for it.There are a total of 20 terminations on it.In this case, the device is located at terminal DUAL.Total number of pins is 20.High efficiency is possible at a voltage of 4.5V.Surface Mount has set it up this way.In the electrical industry, this component is categoriHot Swap Controllered as Hot Swap Controller.Ensure reliable operation by setting the temperature to -40°C~85°C.Devices with General Purpose applications are available.The article is featured in Latched Fault, UVLO.Hot-swappable device should work if you use a 3V~13V 3V~5.5VV power source.TPS2301 numbers belong to this family.This device operates by using 20 pins.Power Management Circuits contains this gadget on its own.Programmable features include Circuit Breaker, Fault Timeout, Slew Rate.Hot-swappable device is estimated that there is a current supply of 5μA.Positioned in direction of Surface Mount, it is at a right angle.Normally, Vsup should remain above 3V.Hot Swap is possible to achieve high efficiency wHot Swaph a 21V output voltage.
TPS2301IPWRG4 Features
The terminal position of 20
Features of Latched Fault, UVLO
Programmable features of Circuit Breaker, Fault Timeout, Slew Rate
Output voltage of 21V
TPS2301IPWRG4 Applications
There are a lot of Texas Instruments TPS2301IPWRG4 hot swap controllers applications.
- Active current limit
- Industrial high-side switches
- Power supply hotswap & inrush control
- Firewire
- Current monitoring
- Electric vehicle
- Reverse current protection
- DC boost circuit
- Backplane
- Disconnect faulty loads before supply voltage drops
