banner_page

TPS27081ADDCR

0.95mm PMIC TPS27081 6 Pin 5V SOT-23-6 Thin, TSOT-23-6


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-TPS27081ADDCR
  • Package: SOT-23-6 Thin, TSOT-23-6
  • Datasheet: -
  • Stock: 225
  • Description: 0.95mm PMIC TPS27081 6 Pin 5V SOT-23-6 Thin, TSOT-23-6 (Kg)

Details

Tags

Parameters
Interface On/Off
Output Configuration High Side
Power Dissipation 1.19W
Output Current 3A
Voltage - Supply (Vcc/Vdd) Not Required
Switch Type General Purpose
Nominal Input Voltage 8V
Ratio - Input:Output 1:1
Voltage - Load 1.2V~8V
Number of Drivers 2
Rds On (Typ) 32m Ω
Built-in Protections TRANSIENT
Height 1.1mm
Length 2.9mm
Width 1.6mm
Thickness 870μm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 5 days ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case SOT-23-6 Thin, TSOT-23-6
Number of Pins 6
Weight 36.003894mg
Operating Temperature -40°C~85°C TA
Packaging Cut Tape (CT)
JESD-609 Code e3
Feature Slew Rate Controlled
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 6
ECCN Code EAR99
Resistance 82mOhm
Terminal Finish Matte Tin (Sn)
Max Power Dissipation 1.19W
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 5V
Terminal Pitch 0.95mm
Base Part Number TPS27081
Number of Outputs 1
Max Output Current 3A
Supply Voltage-Max (Vsup) 8V
Supply Voltage-Min (Vsup) 1V

TPS27081ADDCR Description

The TPS27081ADDCR is a high-side Load Switch that features industry-standard ESD protection on all pins providing better ESD compatibility with other onboard components. The TPS27081A level shifts ON/OFF logic signal to VIN levels and support as low as 1-V CPU or MCU logic to control higher voltage power supplies without requiring an external level-shifter. Switching a large value output capacitor CL through a fast ON/OFF logic signal may result in an excessive inrush current. To control the load inrush current, connect a resistor R2 and add an external capacitor C1 as shown in the Simplified Schematic in the Technical Data Sheet. To configure the TPS27081A to achieve a specific slew rate, refer to the Application and Implementation section. A single pull-up resistor R1 is required in standby power switch applications. In such applications connect the R2 pin of the TPS27081A to the system ground when inrush current control is not required.



TPS27081ADDCR Features

Adjustable turn-on and turnoff slew rate control through external R1, R2, and C1

Supports a wide range of 1.2 to 8V supply inputs

Integrated NMOS for PFET control

Full ESD protection (all pins)

Low ON-resistance, high-current PFET

Ultralow leakage current in standby (typical 100nA)



TPS27081ADDCR Applications

Industrial, Power Management



Write a review

Note: HTML is not translated!
    Bad           Good