TPS3110E12DBVT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 437mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.2V |
| Terminal Pitch | 0.95mm |
| Base Part Number | TPS3110E12 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 6 |
| Number of Channels | 1 |
| Max Supply Voltage | 3.3V |
| Min Supply Voltage | 400mV |
| Operating Supply Current | 1.2μA |
| Power Dissipation | 437mW |
| Max Supply Current | 27μA |
| Adjustable Threshold | NO |
| Quiescent Current | 1.2μA |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 65ms Minimum |
| Min Reset Threshold Voltage | 1.133V |
| Max Reset Threshold Voltage | 1.151V |
| Threshold Voltage | 1.142 |
| Undervoltage Threshold | 1.142V |
| Overvoltage Threshold | 1.151V |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
TPS3110E12DBVT Overview
There are 6 terminals on this power management that allow it to be mounted. There is a Tape & Reel (TR)-packaging method applied to IC management. In this IC power you will find 1 functions for you to refer to. Depending on the power managment ic you are looking at, you can find a total of 1 channels. There are SOT-23-6 functions included in this PMIC so that you can refer to them. Several of the benefits of this PMIC are also shared by other Simple Reset/Power-On Reset products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. Manage ics operate at 1.2V supply voltages. There is a voltage supply of 1 for the PMIC chip, and the chip conducts at that voltage. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. In total, IC powers are 6 pins on the board. Pin count of the power management is 6. A voltage (Vsup) that doesn't fall below 400mV as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 3.3V volts. The recommended mounting type is Surface Mount. We recommend setting the supervisors to -40°C~85°C TJ degrees. The output voltage of this power managment ic during operation is Push-Pull, Totem Pole. The power management's supply current is 1.2μA. For similar manage ics search of the manufacturer, you can always refer to TPS3110E12, the base PMIC number. The maximum supply temperature that PMIC chip can work with is 27μA.
TPS3110E12DBVT Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 400mV
1.2μA operating supply current
TPS3110E12DBVT Applications
There are a lot of Texas Instruments TPS3110E12DBVT Voltage Supervisors applications.
- Important electronics for automotive safety
- Detection of phase sequence
- Personal computers
- Insulation fault location system
- Military communications
- Smartphones
- Consumer electronics
- Digitally controlled LDO regulators circuit
- Automotive permanent magnet synchronous motors
- Military electronics
