Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 5 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
5-TSSOP, SC-70-5, SOT-353 |
Surface Mount |
YES |
Number of Pins |
5 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Cut Tape (CT) |
Series |
Automotive, AEC-Q100 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Type |
Multi-Voltage Supervisor |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Power Management Circuits |
Max Power Dissipation |
321mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
1.5V |
Base Part Number |
TPS3805H33 |
Output |
Push-Pull, Totem Pole |
Pin Count |
5 |
Operating Supply Voltage |
5.5V |
Number of Channels |
1 |
Max Supply Voltage |
6V |
Min Supply Voltage |
1.3V |
Operating Supply Current |
3μA |
Nominal Supply Current |
3μA |
Power Dissipation |
321mW |
Max Supply Current |
6μA |
Adjustable Threshold |
YES |
Quiescent Current |
3μA |
Watchdog Timer |
No |
Reset |
Active Low |
Voltage - Threshold |
3.05V Adj |
Number of Voltages Monitored |
2 |
Reset Timeout |
5μs Typical Propagation Delay |
Threshold Voltage |
3 |
Undervoltage Threshold |
3.06V |
Overvoltage Threshold |
3.096V |
Reset Delay Time |
5.5 μs |
Height |
1.1mm |
Length |
2mm |
Width |
1.25mm |
Thickness |
900μm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TPS3805H33QDCKRQ1 Overview
There are 5 terminals on this power management that allow it to be mounted. Cut Tape (CT)-packaging is used. There are 1 functions included in this PMIC so that you can refer to them. A series of 1 channels can be found on this supervisor. In this PMIC, you can find 5-TSSOP, SC-70-5, SOT-353 functions for your reference. There are a lot of similarities between this IC management and other Multi-Voltage Supervisor products. Packages are specified to have an average peak reflow temperature of 260. The supervisor is always powered by a 1.5V volt supply. During operation, the power ic is supplied with a voltage of 2. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. In total, IC powers are 5 pins on the board. Pin count of the power management is 5. There should be a minimum voltage supply (Vsup) of 1.3V for this PMIC. During this IC power, the maximum supply voltage (Vsup) should not exceed 6V volts. The recommended mounting type is Surface Mount. This power management is the recommended temperature range for the supervisors: -40°C~125°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. Supplied with a operating current of 3μA, this PMIC is capable of fully function as specified. It is always advisable to use TPS3805H33, the base supervisor number, when searching for similar PMICs from the manufacturer. A maximum supply temperature of 6μA can be used. Located in the well-known Automotive, AEC-Q100 series product line, this IC management is a kind of this series.
TPS3805H33QDCKRQ1 Features
Multi-Voltage Supervisor type
Minimum supply voltage of 1.3V
3μA operating supply current
TPS3805H33QDCKRQ1 Applications
There are a lot of Texas Instruments TPS3805H33QDCKRQ1 Voltage Supervisors applications.
- Rechargeable batteries
- Detection of phase loss
- Power communication system
- Radio
- Analog circuit
- Leakage protection
- DVR
- Medical-specific isolation transformer
- Insulation fault location system
- Electronics installed in the vehicle