Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-6 |
Surface Mount |
YES |
Number of Pins |
6 |
Weight |
36.003894mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Cut Tape (CT) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
ECCN Code |
EAR99 |
Type |
Multi-Voltage Supervisor |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Additional Feature |
DETECTION THRESHOLD VOLTAGE IS 3V |
Subcategory |
Power Management Circuits |
Max Power Dissipation |
437mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3.3V |
Terminal Pitch |
0.95mm |
Base Part Number |
TPS3806I33 |
Output |
Open Drain or Open Collector |
Pin Count |
6 |
Number of Channels |
2 |
Max Supply Voltage |
6V |
Min Supply Voltage |
1.3V |
Operating Supply Current |
3μA |
Nominal Supply Current |
4μA |
Power Dissipation |
437mW |
Max Supply Current |
6μA |
Adjustable Threshold |
YES |
Quiescent Current |
3μA |
Watchdog Timer |
No |
Reset |
Active Low |
Voltage - Threshold |
3V Adj |
Number of Voltages Monitored |
2 |
Reset Timeout |
5μs Typical Propagation Delay |
Threshold Voltage |
3 |
Undervoltage Threshold |
3V |
Overvoltage Threshold |
3.022V |
Height |
1.45mm |
Length |
2.9mm |
Width |
1.6mm |
Thickness |
1.2mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TPS3806I33DBVR Overview
Power management is mounted through 6 terminals. Packaging is in the form of a Cut Tape (CT). In this PMIC, you can find 1 functions for your reference. A series of 2 channels can be found on this supervisor. There are SOT-23-6 functions included in this PMIC so that you can refer to them. This IC power shares lots of benefits with other Multi-Voltage Supervisor products. Specifies a reflow peak temperature of 260 for the package during reflow. The supervisor is always powered by a 3.3V volt supply. Power management conducts at a voltage of 2. It is possible to subcategorize this power ic as a Power Management Circuits chip. It has a total of 6 pins that are attached to IC management. 6 pins are present on the power management system. There should be a minimum voltage supply (Vsup) of 1.3V for this PMIC. In this PMIC, the maximum supply voltage (Vsup) should not exceed 6V volts. Mounting type Surface Mount is recommended. Temperature setting for the supervisors should be -40°C~85°C TA. While this power management is operating, it will output Open Drain or Open Collector as the output voltage. There is a supply current of 3μA for the power management. Additionally, IC management are a variety of features, for example [0], to name a few. It is always advisable to use TPS3806I33, the base supervisor number, when searching for similar PMICs from the manufacturer. Voltage supervisor can work with a supply temperature of 6μA at the most.
TPS3806I33DBVR Features
Multi-Voltage Supervisor type
Minimum supply voltage of 1.3V
3μA operating supply current
TPS3806I33DBVR Applications
There are a lot of Texas Instruments TPS3806I33DBVR Voltage Supervisors applications.
- Detection of phase sequence
- Battery cars
- Analog circuit
- Power distribution systems of operating room
- Electric heating appliances
- Digitally controlled LDO regulators circuit
- Radar
- Smart meter
- Electronics installed in the vehicle
- Rechargeable batteries