TPS3838E18DBVT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 437mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | TPS3838E18 |
| Output | Open Drain or Open Collector |
| Pin Count | 5 |
| Max Output Current | 5mA |
| Operating Supply Voltage | 1.8V |
| Number of Channels | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 250nA |
| Nominal Supply Current | 15μA |
| Power Dissipation | 437mW |
| Max Supply Current | 15μA |
| Adjustable Threshold | NO |
| Quiescent Current | 220nA |
| Reset | Active Low |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 10ms Minimum |
| Min Reset Threshold Voltage | 1.66V |
| Max Reset Threshold Voltage | 1.74V |
| Undervoltage Threshold | 1.71V |
| Overvoltage Threshold | 1.74V |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS3838E18DBVT Overview
As you can see, this power management is mounted through 5 terminals. Cut Tape (CT)-packaging is used. To assist you, this IC power includes 1 functions. Power management consists of 1 channels, each of which can be used independently. As a reference, this IC power includes SC-74A, SOT-753 functions for your convenience. There are many benefits that this IC power shares with other Simple Reset/Power-On Reset products as well. Specifies a reflow peak temperature of 260 for the package during reflow. A supply voltage of 1.8V is used to conduct the PMIC chip. When 1 is applied to the power ic, it conducts. The power management is mounted by Surface Mount. The total number of pins on this power management is 5. There are 5 pins on the supervisor. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.6V. During this IC power, the maximum supply voltage (Vsup) should not exceed 6V volts. Mounting type Surface Mount is recommended. The temperature of the supervisors should be set to this range: -40°C~85°C TA. As a result of this supervisor's operation, the output voltage is Open Drain or Open Collector. The supply current of the power management is 250nA. It is always advisable to use TPS3838E18, the base supervisor number, when searching for similar PMICs from the manufacturer. At the most, voltage supervisor can work with a supply temperature of 15μA.
TPS3838E18DBVT Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.6V
250nA operating supply current
TPS3838E18DBVT Applications
There are a lot of Texas Instruments TPS3838E18DBVT Voltage Supervisors applications.
- Microprocessor system
- Kitchen appliances
- Consumer electronics
- Battery cars
- Utility meter
- Radar
- Detection of phase sequence
- Battery cars
- Network equipment
- DC stabilized power supply module
