TPS40009DGQ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Frequency | 600kHz |
| Base Part Number | TPS40009 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 4V |
| Output Type | Transistor Driver |
| Max Output Current | 15A |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 15A |
| Voltage - Supply (Vcc/Vdd) | 2.25V~5.5V |
| Quiescent Current | 1.5mA |
| Control Features | Current Limit, Enable, Soft Start |
| Topology | Buck |
| Min Input Voltage | 2.25V |
| Control Mode | VOLTAGE-MODE |
| Max Input Voltage | 5.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Nominal Input Voltage | 5V |
| Min Output Voltage | 700mV |
| Switcher Configuration | PUSH-PULL |
| Duty Cycle (Max) | 93% |
| Clock Sync | No |
| Height | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40009DGQ Overview
Capsuled in the 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad package, the switching controller suits most application needs. The dc motor controller is adquate to generate for 1 outputs. PMIC is packaged in a solid enclosure of Tube. The system can process Transistor Driver dc switching's outputs (s). dc control's supply and operating voltages are 2.25V~5.5V. Suitable for a -40°C~85°C TA dc switcher. Surface Mount makes it suitable for general dc dc regulator. For efficient switching control, the dcdc regulator features Current Limit, Enable, Soft Start. An analog IC SWITCHING CONTROLLER is connected to the switch converters. Thare switching converters has a terminal (s) at DUAL . A variety of 10 terminations are available in dc switching. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. It is inputted with a DC switcher's voltage of 5V. Searching "TPS40009" will return other relevant dc to dc converter ics. The switching converter has a total of 10 pins. According to the test statistics, DC regulator outputs 4V voltage. If you are starting a new project, you should note the dc dc regulator's typical output current is 15A. The Surface Mount makes DC switcher suitable for most applications and prototypes. A frequency of 600kHz is used by the switching controller. A dc switching in a dormant state uses 1.5mA. 5V is the nominal working voltage. Since the dc switcher's maximum input voltage is 5.5V, the voltage must be regulated accordingly. Voltage 2.25V must be supplied. A dc switcher can only produce an output current of 15A. A voltage controller's lowest output voltage cannot be less than 700mV.
TPS40009DGQ Features
Transistor Driver Outputs
Current Limit, Enable, Soft Start
PULSE WIDTH MODULATION
Frequency: 600kHz
TPS40009DGQ Applications
There are a lot of Texas Instruments TPS40009DGQ DC to DC converter applications.
- Medical equipment
- Terrestrial set-top boxes
- Sink circuits
- Thermal power
- Printing
- Digital display device
- Computer monitoring equipment of building
- Ball screw pair
- Driver circuits
- Production lines
