TPS40020PWPR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-PowerTSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 62.709145mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Base Part Number | TPS40020 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 4V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 5.5V |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 15A |
| Voltage - Supply (Vcc/Vdd) | 2.25V~5.5V |
| Quiescent Current | 1.5mA |
| Control Features | Current Limit, Enable, Frequency Control, Power Good, Soft Start |
| Input Voltage (Min) | 2.25V |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 100kHz~1MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 1.1MHz |
| Duty Cycle (Max) | 95% |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40020PWPR Overview
In the 16-PowerTSSOP (0.173, 4.40mm Width) package, the switching controller meets most application requirements. This dc motor controller can be used to generate outputs with 1 numbers. PMIC packaging is solid with a Tape & Reel (TR) enclosure. Transistor Driver dc switching's outputs (s) are supported. A 2.25V~5.5V voltage is supplied to the dc control and used for operating it. Suitable for work in a -40°C~85°C TA dc switcher. In this switching controller, the switch can be set to 100kHz~1MHz. As it has a Surface Mount value, it can be used for general dc dc regulator. Current Limit, Enable, Frequency Control, Power Good, Soft Start is used for efficient switching control in the dcdc regulator. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. switching converters terminal (s) are designed to be at DUAL. Different dc switching's functions can be applied to 16 terminations. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. DC switcher's input voltageis 5V volts. Other relevant dc to dc converter ics can be found by searching "TPS40020". The switching converter has a total of 16 pins. The type is a particular Switching Regulator or Controllers of switching converter. dc dc voltage regulators should have a minimum input voltage of 2.25V. According to the test statistics, DC regulator outputs 4V voltage. In most cases, the dc dc regulator's output current is 15A. This information should be noted when you begin working with the component. In most applications and prototype designs, DC switcher is qualified as a Surface Mount. This dc regulatorhas a max frequency of 1.1MHz. In order for the voltage regulator dc to dc to perform safely and reliably in a circuit, users are advised to apply 5.5V. Dormant dc switchings use 1.5mA.
TPS40020PWPR Features
Transistor Driver Outputs
Switching Frequency: 100kHz~1MHz
Current Limit, Enable, Frequency Control, Power Good, Soft Start
PULSE WIDTH MODULATION
TPS40020PWPR Applications
There are a lot of Texas Instruments TPS40020PWPR DC to DC converter applications.
- Shearing machines
- Household control circuits
- Electrical distribution systems
- Geothermal power
- Experimental setup
- Solar power plants
- Product burn-in
- Wide-range voltage regulation circuits
- Power supplies of electronic gadgets
- Photovoltaic power
