TPS40180RGETG4
| Parameters | |
|---|---|
| Lifecycle Status | NRND (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 24-VFQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 24 |
| Weight | 45.387587mg |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | ALSO OPERATES IN ADJUSTABLE MODE FROM 0.8 TO 5.8V |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS40180 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 5.8V |
| Output Type | Transistor Driver |
| Max Output Current | 25A |
| Operating Supply Voltage | 40V |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~15V |
| Control Features | Current Limit, Frequency Control, Phase Control, Power Good, Soft Start |
| Max Output Voltage | 5.8V |
| Topology | Buck |
| Min Input Voltage | 2V |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 150kHz~1MHz |
| Max Input Voltage | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Min Output Voltage | 700mV |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 1MHz |
| Duty Cycle (Max) | 87.5% |
| Clock Sync | No |
| Height | 1mm |
| Length | 4mm |
| Width | 4mm |
| Thickness | 880μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40180RGETG4 Overview
As a result of 24-VFQFN Exposed Pad compact design, the switching controller is compatible with most applications. There is enough capacity in the dc motor controller to generate the output for the 1 input. PMIC is packaged in a solid enclosure of Tape & Reel (TR). The program can handle Transistor Driver dc switching's outputs (s). dc control's supply and operating voltages are 4.5V~15V. Suitable for a -40°C~105°C TA dc switcher. The switching controller can be switched at 150kHz~1MHz. The Surface Mount allows it to be used for dc dc regulator in general. Current Limit, Frequency Control, Phase Control, Power Good, Soft Start is used for efficient switching control in the dcdc regulator. Switch converters are connected to ICs with SWITCHING CONTROLLER analog outputs. QUAD are the position of the terminal of the switching converters. Different dc switching's functions can be applied to 24 terminations. This dc dc converter ic uses a variety of control techniques, including PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 12V. Searching "TPS40180" will return other relevant dc to dc converter ics. There are a total of 24 pins on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. According to the test statistics, DC regulator outputs 5.8V voltage. In most cases, the dc dc regulator's output current is 25A. This information should be noted when you begin working with the component. The max frequency of the pmic can reach 1MHz. As a result, DC to DC voltage regulator has a value of ALSO OPERATES IN ADJUSTABLE MODE FROM 0.8 TO 5.8V so that the need can be met more directly. A circuit should contain 40V in order to ensure the voltage regulator dc to dc runs safely and reliably. Since the dc switcher's maximum input voltage is 40V, the voltage must be regulated accordingly. Voltage 2V must be supplied. Input current cannot exceed 25A with this dc switcher. A datasheet states that the switching converter can output 5.8V volts at its maximum. The voltage controller's lowest voltage output is not less than 700mV.
TPS40180RGETG4 Features
Transistor Driver Outputs
Switching Frequency: 150kHz~1MHz
Current Limit, Frequency Control, Phase Control, Power Good, Soft Start
PULSE WIDTH MODULATION
ALSO OPERATES IN ADJUSTABLE MODE FROM 0.8 TO 5.8V
TPS40180RGETG4 Applications
There are a lot of Texas Instruments TPS40180RGETG4 DC to DC converter applications.
- Post equipment
- Correction machines
- Gear/thread machining machines
- Bending machines
- Product testing
- Smoke exhaust equipment
- Automation technology
- Overvoltage protection circuits in TV sets
- Servo drive system
- Radio equipment
