TPS40190DRCRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Weight | 26.109911mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS40190 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 12.75V |
| Output Type | Transistor Driver |
| Max Output Current | 20A |
| Operating Supply Voltage | 15V |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~15V |
| Quiescent Current | 2.5mA |
| Control Features | Enable |
| Max Output Voltage | 12.75V |
| Topology | Buck |
| Min Input Voltage | 4.5V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 300kHz |
| Max Input Voltage | 15V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Min Output Voltage | 600mV |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 360kHz |
| Duty Cycle (Max) | 85% |
| Clock Sync | No |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40190DRCRG4 Overview
With a 10-VFDFN Exposed Pad package, the switching controller is suitable for a wide range of applications. There is sufficient capacity to generate switching controller for outputs 1. The pmic is packaged in Tape & Reel (TR) solid enclosure. With Transistor Driver dc switching's output (s), it is able to handle it. Voltages 4.5V~15V are the dc control's supply voltage and operating voltage, respectively. Suitable for working in an dc switcher that has a -40°C~85°C TA. In this switching controller, the switch can be set to 300kHz. As it has a Surface Mount value, it can be used for general dc dc regulator. Enable is used for efficient switching control in the dcdc regulator. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. A switching converters's terminal (s) sits at the DUAL position. A variety of dc switching's functions can be performed on 10 terminations. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. DC switcher's voltage input of 12V. Search for "TPS40190" to find other relevant dc to dc converter ics. There are only 10 pins on switching converter. Based on the test statistics, DC regulator outputs voltage 12.75V. normally, the dc dc regulator's output current is 20A, which you should keep in mind when starting a project. DC regulator has a maximum frequency of 360kHz. For safe and reliable operation in a circuit, voltage regulator dc to dc is suggested that users apply 15V. A dc switching in a dormant state uses 2.5mA. The maximum input voltage of this dc switcher is 15V, so users must limit the voltage accordingly. Voltage 4.5V is needed for the supply. There will be 20A current output from the dc switcher above 20A. Datasheets indicate that the switching converter can output 12.75V volts at its maximum. A voltage controller's lowest output voltage cannot be less than 600mV.
TPS40190DRCRG4 Features
Transistor Driver Outputs
Switching Frequency: 300kHz
Enable
PULSE WIDTH MODULATION
TPS40190DRCRG4 Applications
There are a lot of Texas Instruments TPS40190DRCRG4 DC to DC converter applications.
- Digital precision reference circuits
- ATMs
- Linear guide
- Thermal power
- Grinders
- Mobile phones
- Arc suppression circuits
- Photovoltaic power
- Smoke prevention equipment
- Pipe bending machines
