TPS40193DRCT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Weight | 26.109911mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 2.61W |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Frequency | 300kHz |
| Base Part Number | TPS40193 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 14.4V |
| Output Type | Transistor Driver |
| Max Output Current | 20A |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~18V |
| Quiescent Current | 2.5mA |
| Control Features | Enable, Power Good |
| Max Output Voltage | 14.4V |
| Topology | Buck |
| Min Input Voltage | 4.5V |
| Control Mode | VOLTAGE-MODE |
| Max Input Voltage | 18V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Min Output Voltage | 591mV |
| Switcher Configuration | PUSH-PULL |
| Duty Cycle (Max) | 85% |
| Clock Sync | No |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40193DRCT Overview
The switching controller fits in the 10-VFDFN Exposed Pad package and is ideal for most applications. For 1 outputs, the dc motor controller is appropriate. Packaging for the pmic consists of Tape & Reel (TR) solid enclosures. Transistor Driver dc switching's outputs (s) can be handled by it. DC control operates at 4.5V~18V volts and has 4.5V~18V supply voltage. Workable in an dc switcher where -40°C~85°C TA is the -40°C~85°C TArm. As it has a Surface Mount value, it can be used for general dc dc regulator. In order to control switching efficiently, the dcdc regulator features Enable, Power Good. A SWITCHING CONTROLLER analog IC is connected to the switch converters. switching converters terminal (s) are designed to be at DUAL. A variety of 10 terminations are available in dc switching. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 12V. Searching "TPS40193" will return other relevant dc to dc converter ics. The switching converter has a total of 10 pins. As determined by the test statistics, the output voltage of DC regulator is 14.4V. In most cases, the output current of the dc dc regulator will be 20A, so note that when you start the project. Switching controllers operate at 300kHz frequencies. A dc switching in a dormant state uses 2.5mA. Users must limit the voltage accordingly because the dc switcher's maximum input voltage is 18V. Voltage 4.5V is needed for the supply. DC switchers cannot produce output currents greater than 20A. The datasheet indicates that the switching converter can output 14.4V volts at its maximum. At its lowest voltage, the voltage controller does not produce less than 591mV.
TPS40193DRCT Features
Transistor Driver Outputs
Enable, Power Good
PULSE WIDTH MODULATION
Frequency: 300kHz
TPS40193DRCT Applications
There are a lot of Texas Instruments TPS40193DRCT DC to DC converter applications.
- Medical monitoring systems
- CMM
- Electrical power transmission
- Radio equipment
- Direct power supply system
- USB circuits
- Smoke exhaust equipment
- seismic instrument power circuits
- Lathes
- Electric heating, lighting
