TPS40195PW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 900mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 600kHz |
| Base Part Number | TPS40195 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 5.5V |
| Output Type | Transistor Driver |
| Max Output Current | 20A |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Power Dissipation | 900mW |
| Output Current | 1mA |
| Voltage - Supply (Vcc/Vdd) | 4.5V~20V |
| Quiescent Current | 4mA |
| Control Features | Current Limit, Enable, Frequency Control, Power Good, Soft Start |
| Max Output Voltage | 17V |
| Topology | Buck |
| Min Input Voltage | 4.5V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 100kHz~600kHz |
| Max Input Voltage | 20V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Nominal Input Voltage | 12V |
| Min Output Voltage | 591mV |
| Switcher Configuration | PUSH-PULL |
| Input Current | 4mA |
| Duty Cycle (Max) | 85% |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40195PW Overview
With its 16-TSSOP (0.173, 4.40mm Width) package, the switching controller fits the needs of most applications. 1 outputs are supported by the dc motor controller. Packaging for the pmic consists of Tube solid enclosures. With this function, you can deal with Transistor Driver dc switching's outputs (s). 4.5V~20V is the operating voltage and supply voltage of the dc control. Suitable for work in a -40°C~125°C TJ dc switcher. The switching controller is capable of switching at the 100kHz~600kHz position. The Surface Mount makes it ideal for general dc dc regulator. Current Limit, Enable, Frequency Control, Power Good, Soft Start is used for efficient switching control in the dcdc regulator. A SWITCHING CONTROLLER analog IC is connected to the switch converters. A switching converters's terminal (s) sits at the DUAL position. The 16 terminations can be used for a wide range of dc switching. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. DC switcher's input voltageis 12V volts. You can find other relevant dc to dc converter ics by searching "TPS40195". Switching converter has a total of 16 pins. DC regulator outputs 5.5V voltage based on test statistics. If you are starting a new project, you should note the dc dc regulator's typical output current is 1mA. A frequency of 600kHz is used by the switching controller. A dc switching in a dormant state uses 4mA. 12V is the nominal working voltage. Because the dc switcher's maximum input voltage is 20V users must limit the voltage accordingly. Switching controller is necessary to have a supply voltage of 4.5V. There will be 20A output current greater than 20A from the dc switcher. The datasheet indicates that the switching converter can output 17V volts at its maximum. Lowest voltage output of the voltage controller must be greater than 591mV. For operation, the switching converter could be satisfied with 4mA current flow input.
TPS40195PW Features
Transistor Driver Outputs
Switching Frequency: 100kHz~600kHz
Current Limit, Enable, Frequency Control, Power Good, Soft Start
PULSE WIDTH MODULATION
Frequency: 600kHz
TPS40195PW Applications
There are a lot of Texas Instruments TPS40195PW DC to DC converter applications.
- Production lines
- USB circuits
- Low output voltage switching power supply circuits
- Wide-range voltage regulation circuits
- Special machining machine tools
- Motor controller circuits
- Experimental setup
- Plate bending machines
- Cutting machine tools
- Telecommunications equipment
