TPS40210DGQG4
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS40210 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 260V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Output Configuration | Positive |
| Output Current | 400mA |
| Voltage - Supply (Vcc/Vdd) | 4.5V~52V |
| Control Features | Enable, Frequency Control, Soft Start |
| Max Output Voltage | 9V |
| Topology | Boost, Flyback, SEPIC |
| Min Input Voltage | 4.5V |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 35kHz~1MHz |
| Max Input Voltage | 52V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Max Frequency | 1MHz |
| Max Duty Cycle | 95 % |
| Clock Sync | Yes |
| Duty Cycle | 95 % |
| Height | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| RoHS Status | ROHS3 Compliant |
TPS40210DGQG4 Overview
It comes in the 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad package, which makes switching controller suitable for most applications. 1 outputs can be generated with the dc motor controller. An enclosure of Tube is used to package the PMIC. There are Transistor Driver dc switching's output (s) that it can handle. Voltages 4.5V~52V are the dc control's supply voltage and operating voltage, respectively. Suitable for a -40°C~125°C TJ dc switcher. It can switch at 35kHz~1MHz. As it has a Surface Mount value, it can be used for general dc dc regulator. For efficient switching control, the dcdc regulator features Enable, Frequency Control, Soft Start. An analog IC with the SWITCHING REGULATOR signal is connected to the switch converters. DUAL are the position of the terminal of the switching converters. 10 terminations with a variety of function. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 12V is input. TPS40210 can be searched for other relevant dc to dc converter ics. Total pins of switching converter are 10. Switching converter is a type of Switching Regulator or Controllers in particular. Statistically, DC regulator outputs 260V volts. If you are starting a new project, you should note the dc dc regulator's typical output current is 400mA. As a result of this, the maximum duty cycle of the voltage regulator dc to dc must remain 95 % during power-up and power-down. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. DC regulator's maximum frequency is 1MHz. The dc switcher's maximum input voltage is 52V, so users must limit the voltage accordingly. A voltage of 4.5V is required for the supply. Depending on the datasheet, the switching converter can output 9V volts at its peak.
TPS40210DGQG4 Features
Transistor Driver Outputs
Switching Frequency: 35kHz~1MHz
Enable, Frequency Control, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 95 %
TPS40210DGQG4 Applications
There are a lot of Texas Instruments TPS40210DGQG4 DC to DC converter applications.
- Die casting equipment
- Domestic water pumps
- Digital display device
- Hydro power
- Solar power plants
- Scientific research
- Production lines
- Industrial controllers
- Household control circuits
- Smoke prevention equipment
