TPS40211DRCR
| Parameters | |
|---|---|
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Weight | 26.109911mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS40211 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 250V |
| Output Type | Transistor Driver |
| Max Output Current | 6A |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Output Configuration | Positive |
| Output Current | 400mA |
| Voltage - Supply (Vcc/Vdd) | 4.5V~52V |
| Quiescent Current | 1.5mA |
| Control Features | Enable, Frequency Control, Soft Start |
| Topology | Boost, Flyback, SEPIC |
| Min Input Voltage | 4.5V |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 35kHz~1MHz |
| Max Input Voltage | 52V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Max Frequency | 1MHz |
| Max Duty Cycle | 95 % |
| Clock Sync | Yes |
| Duty Cycle | 95 % |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
TPS40211DRCR Overview
It comes in the 10-VFDFN Exposed Pad package, which makes switching controller suitable for most applications. 1 outputs can be generated with the dc motor controller. The pmic is packaged in Tape & Reel (TR) solid enclosure. There are Transistor Driver dc switching's output (s) that it can handle. dc control's supply and operating voltages are 4.5V~52V. Suitable for a -40°C~125°C TJ dc switcher. Using this switching controller, it is possible to switch at 35kHz~1MHz. A generalization of dc dc regulator can be made using Surface Mount. Featured in the dcdc regulator is Enable, Frequency Control, Soft Start which allows efficient switching control. The switch converters are connected to a SWITCHING REGULATOR analog IC. Switching converters are designed with the terminal (s) at position DUAL . 10 terminations with a variety of function. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. A DC switcher's nominal voltage of 12V is input. Other relevant dc to dc converter ics can be found by searching "TPS40211". Total pins of switching converter are 10. Specifically, switching converter falls under the Switching Regulator or Controllers category. Based on the test statistics, DC regulator outputs voltage 250V. A starting point for a project is to note down the dc dc regulator's usual output current, which is 400mA. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 95 %. There is a maximum frequency of 1MHz on this dc regulators. The dc switching utilizes 1.5mA when it is in a dormant state. The maximum input voltage of dc switcher is 52V, so users should limit their voltage accordingly. Voltage 4.5V is necessary for the supply. DC switchers cannot produce output currents greater than 6A.
TPS40211DRCR Features
Transistor Driver Outputs
Switching Frequency: 35kHz~1MHz
Enable, Frequency Control, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 95 %
TPS40211DRCR Applications
There are a lot of Texas Instruments TPS40211DRCR DC to DC converter applications.
- Flexible manufacturing cells
- Industrial robots
- ATMs
- Smart grid
- Flaw detection equipment
- Alternators
- Experimental setup
- Precision electronic equipment
- Sensitive electronic devices
- Combined machine tools
