TPS40211DRCT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Weight | 26.109911mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Frequency | 1MHz |
| Base Part Number | TPS40211 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 250V |
| Output Type | Transistor Driver |
| Max Output Current | 6A |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Output Configuration | Positive |
| Output Current | 6A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~52V |
| Max Supply Current | 2.5mA |
| Quiescent Current | 1.5mA |
| Control Features | Enable, Frequency Control, Soft Start |
| Topology | Boost, Flyback, SEPIC |
| Min Input Voltage | 4.5V |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 35kHz~1MHz |
| Max Input Voltage | 52V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Max Duty Cycle | 95 % |
| Clock Sync | Yes |
| Duty Cycle | 95 % |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40211DRCT Overview
With a 10-VFDFN Exposed Pad package, the switching controller is suitable for a wide range of applications. It is sufficient to generate 1 outputs with this dc motor controller. There is a Tape & Reel (TR) solid enclosure around the pmic. The system can process Transistor Driver dc switching's outputs (s). dc controls with 4.5V~52V voltage are supplied and operated. Suitable for a -40°C~125°C TJ dc switcher. There is a switch at 35kHz~1MHz that can be used with this controller. dc dc regulator can be generalized using Surface Mount. The dcdc regulator features Enable, Frequency Control, Soft Start for efficient switching control. Switch converters are connected to ICs with SWITCHING REGULATOR analog outputs. Terminal (s) of the switching converters are designed at the DUAL position. Various 10 terminations. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. There is a DC switcher's nominal voltage of 12V. You can find other relevant dc to dc converter ics by searching "TPS40211". Switching converter has a total of 10 pins. Specially, switching converter corresponds to type Switching Regulator or Controllers. According to the test statistics, DC regulator outputs 250V voltage. If you start a project, note down the dc dc regulator's usual output current of 6A. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 95 %. There is 1MHz frequency setting on the switching controller. Dormant dc switchings use 1.5mA. The dc switcher's maximum input voltage is 52V, so users must limit the voltage accordingly. 4.5V is the required supply voltage. There will be 6A output current greater than 6A from the dc switcher. Continually operating at more than 2.5mA may cause malfunctions and damage to the component.
TPS40211DRCT Features
Transistor Driver Outputs
Switching Frequency: 35kHz~1MHz
Enable, Frequency Control, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 95 %
Frequency: 1MHz
TPS40211DRCT Applications
There are a lot of Texas Instruments TPS40211DRCT DC to DC converter applications.
- Electric heating, lighting
- Wind power
- Geothermal power
- Mobile phones
- Radio equipment
- Electric water heaters
- Computer-related products
- Game consoles
- Television equipment
- Automation technology
