TPS40304ADRCT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS40304 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 6.5V |
| Output Type | Transistor Driver |
| Max Output Current | 25A |
| Operating Supply Voltage | 20V |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | 3V~20V |
| Quiescent Current | 2.5mA |
| Control Features | Enable, Power Good, Soft Start |
| Max Output Voltage | 18V |
| Topology | Buck |
| Min Input Voltage | 3V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 600kHz |
| Max Input Voltage | 20V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 660kHz |
| Max Duty Cycle | 90 % |
| Clock Sync | No |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40304ADRCT Overview
This switching controller fits most application requirements since it is packaged in a 10-VFDFN Exposed Pad package. This dc motor controller can be used to generate outputs with 1 numbers. An enclosure of Tape & Reel (TR) is used to package the PMIC. The program can handle Transistor Driver dc switching's outputs (s). This dc control has a supply voltage and operating voltage of 3V~20V. Worked in a -40°C~125°C TJ dc switcher before. This switching controller can switch at 600kHz. It is suitable for general dc dc regulator when it is set to Surface Mount. Featured in the dcdc regulator is Enable, Power Good, Soft Start which allows efficient switching control. The switch converters are connected to a SWITCHING CONTROLLER analog IC. The switching converters's terminal (s) are designed at QUAD . 10 terminations with various dc switching's functions. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. The DC switcher's nominal voltage is 12V. You can find other relevant dc to dc converter ics by searching "TPS40304". The switching converter has a total of 10 pins. DC regulator outputs 6.5V voltage based on test statistics. A starting point for a project is to note down the dc dc regulator's usual output current, which is 25A. Voltage regulator dc to dc is designed to operate at 90 % duty cycle during power-ups and power-downs to ensure reliability. It is estimated that this dc regulatorhas a maximum frequency of 660kHz. Users should apply 20V to operate the voltage regulator dc to dc safely and reliably. In dormant mode, 2.5mA is used. Since the dc switcher's maximum input voltage is 20V, the voltage must be regulated accordingly. Voltage 3V is needed for the supply. There will be 25A current output from the dc switcher above 25A. At its maximum, the switching converter can output 18V volts.
TPS40304ADRCT Features
Transistor Driver Outputs
Switching Frequency: 600kHz
Enable, Power Good, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 90 %
TPS40304ADRCT Applications
There are a lot of Texas Instruments TPS40304ADRCT DC to DC converter applications.
- Radio equipment
- Electric heating, lighting
- Surge protection circuits
- Emergency lighting monitoring equipment
- Domestic water pumps
- Wind power
- Shearing machines
- Drilling machines
- Combined machine tools
- Computer rooms
