TPS43335QDAPRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 38-PowerTSSOP (0.240, 6.10mm Width) |
| Number of Pins | 38 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 38 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | ALSO HAS A CONTROL TECHNIQUE OF PFM; OPERATES IN ADJUSTABLE MODE FROM 0.9 TO 11V |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Base Part Number | TPS43335 |
| Function | Step-Up, Step-Down |
| Number of Outputs | 3 |
| Output Voltage | 11V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 40V |
| Input Voltage-Nom | 13V |
| Analog IC - Other Type | DUAL SWITCHING CONTROLLER |
| Operating Supply Current | 30μA |
| Output Configuration | Positive |
| Output Current | 6A |
| Voltage - Supply (Vcc/Vdd) | 4V~40V |
| Quiescent Current | 30μA |
| Control Features | Enable, Frequency Control, Power Good, Soft Start, Tracking |
| Input Voltage (Min) | 4V |
| Topology | Buck, Boost |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 150kHz~600kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PHASE-SHIFT |
| Max Frequency | 600kHz |
| Max Duty Cycle | 98.75 % |
| Isolation | Non-Isolated |
| Duty Cycle (Max) | 90%, 98.75% |
| Output Phases | 2 |
| Height | 1.2mm |
| Length | 12.5mm |
| Width | 6.2mm |
| Thickness | 1.15mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS43335QDAPRQ1 Overview
Capsuled in the 38-PowerTSSOP (0.240, 6.10mm Width) package, the switching controller can be used for a wide range of applications. 3 outputs can be generated with the dc motor controller. An enclosure of Tape & Reel (TR) is used to package the PMIC. Transistor Driver dc switching's outputs (s) are supported. 4V~40V is the operating voltage and supply voltage of the dc control. Suitable for work in a -40°C~125°C TJ dc switcher. This switching controller can switch at 150kHz~600kHz. dc dc regulator is made easier with Surface Mount. To provide efficient switching control, Enable, Frequency Control, Power Good, Soft Start, Tracking is included in the dcdc regulator. An analog IC with the DUAL SWITCHING CONTROLLER signal is connected to the switch converters. DUAL are the position of the terminal of the switching converters. There are many different types of terminations for 38. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 13V is input. In addition to "TPS43335", there are other relevant dc to dc converter ics you can find. The switching converter has a total of 38 pins. Specifically, switching converter falls under the Switching Regulator or Controllers category. Input voltage of dc dc voltage regulator should be 4V. Statistically, DC regulator outputs 11V volts. It's important to remember that the dc dc regulator's normaloutput current is 6A, so you should note it down when starting a new project. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 98.75 %. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. 600kHz is the maximum frequency of this dc regulators. To better satisfy the need, DC to DC voltage regulator has a value of ALSO HAS A CONTROL TECHNIQUE OF PFM; OPERATES IN ADJUSTABLE MODE FROM 0.9 TO 11V. In order for the voltage regulator dc to dc to perform safely and reliably in a circuit, users are advised to apply 40V. Automotive, AEC-Q100 series dc to dc voltage regulator belong to this series. DC switchings that are dormant use 30μA. 30μA volts is the supply current.
TPS43335QDAPRQ1 Features
Transistor Driver Outputs
Switching Frequency: 150kHz~600kHz
Enable, Frequency Control, Power Good, Soft Start, Tracking
PULSE WIDTH MODULATION
Max Duty Cycle: 98.75 %
ALSO HAS A CONTROL TECHNIQUE OF PFM; OPERATES IN ADJUSTABLE MODE FROM 0.9 TO 11V
TPS43335QDAPRQ1 Applications
There are a lot of Texas Instruments TPS43335QDAPRQ1 DC to DC converter applications.
- Geothermal power
- Cutting machine tools
- Flexible manufacturing cells
- Bending machines
- Smoke exhaust equipment
- Overvoltage protection circuits in TV sets
- PSRR circuits
- Various CNC machine tools
- Medical monitoring systems
- Digital display device
