TPS51218DSCT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | D-CAP™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | ALSO OPERATES IN ADJUSTABLE MODE FROM 0.7V TO 2.6V |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Frequency | 430kHz |
| Base Part Number | TPS51218 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 2.6V |
| Output Type | Transistor Driver |
| Max Output Current | 20A |
| Operating Supply Voltage | 6.5V |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~6.5V |
| Quiescent Current | 320μA |
| Control Features | Enable, Frequency Control, Power Good |
| Max Output Voltage | 2.6V |
| Topology | Buck |
| Min Input Voltage | 3V |
| Control Mode | VOLTAGE-MODE |
| Max Input Voltage | 28V |
| Control Technique | PULSE WIDTH MODULATION |
| Supply Current-Max (Isup) | 0.5mA |
| Synchronous Rectifier | Yes |
| Min Output Voltage | 700mV |
| Switcher Configuration | PUSH-PULL |
| Switching Frequency | 465kHz |
| Clock Sync | No |
| Duty Cycle | 91 % |
| Height | 800μm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 750μm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
TPS51218DSCT Overview
Capsuled in the 10-WFDFN Exposed Pad package, the switching controller suits most application needs. The dc motor controller is adquate to generate for 1 outputs. The pmic is packaged in Tape & Reel (TR) solid enclosure. Transistor Driver dc switching's outputs (s) can be handled by it. dc control's supply and operating voltages are 4.5V~6.5V. Work well in dc switchers with a -40°C~85°C TA. A generalization of dc dc regulator can be made using Surface Mount. Enable, Frequency Control, Power Good provides dcdc regulator efficient switching control. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. Thare switching converters has a terminal (s) at DUAL . Various 10 terminations. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 5V is input. TPS51218 can be used to locate other relevant dc to dc converter ics. There are a total of 10 pins on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. According to the test statistics, DC regulator outputs 2.6V voltage. If you are starting a new project, you should note the dc dc regulator's typical output current is 20A. DC switcher's Surface Mount makes it qualified for most application and prototype designs. DC switcher'sSwitching controller operates at 430kHz Hz. The value of DC to DC voltage regulator is set to ALSO OPERATES IN ADJUSTABLE MODE FROM 0.7V TO 2.6V in order to better satisfy the requirement. For safe and reliable operation in a circuit, voltage regulator dc to dc is suggested that users apply 6.5V. Thare are switch converters of the D-CAP? series. Dormant dc switchings use 320μA. The maximum input voltage of the dc switcher is 28V, so users need to limit the voltage accordingly. Switching controller is necessary to provide a voltage of 5V. Switching controller is necessary to have a supply voltage of 3V. Input current cannot exceed 20A with this dc switcher. The controller should not be supplied with more current than 0.5mA. The switching converter can output 2.6V volts at its utmost, according to the datasheet. Neither the voltage controller's lowest voltage output 700mVr its highest voltage output is less than 700mV. At 465kHz, this controller will mostly work as expected.
TPS51218DSCT Features
Transistor Driver Outputs
Enable, Frequency Control, Power Good
PULSE WIDTH MODULATION
Frequency: 430kHz
ALSO OPERATES IN ADJUSTABLE MODE FROM 0.7V TO 2.6V
Switching Frequency: 465kHz
TPS51218DSCT Applications
There are a lot of Texas Instruments TPS51218DSCT DC to DC converter applications.
- CMM
- Energy management systems
- Medical monitoring systems
- Hydro power
- Wide-range voltage regulation circuits
- Automatic plug-in machines
- Ball screw pair
- Smoke exhaust equipment
- Current source circuits
- Various CNC machine tools
