banner_page

TPS63000IDRCRQ1

10 Terminals 1.8V 10-Pin TPS63000 DC DC Voltage Regulator SWITCHING REGULATOR 1 Outputs 1.25MHz~1.5MHz Tape & Reel (TR) 1.6A Switch 10-VFDFN Exposed Pad


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-TPS63000IDRCRQ1
  • Package: 10-VFDFN Exposed Pad
  • Datasheet: -
  • Stock: 389
  • Description: 10 Terminals 1.8V 10-Pin TPS63000 DC DC Voltage Regulator SWITCHING REGULATOR 1 Outputs 1.25MHz~1.5MHz Tape & Reel (TR) 1.6A Switch 10-VFDFN Exposed Pad (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 2 days ago)
Contact Plating Gold
Mounting Type Surface Mount
Package / Case 10-VFDFN Exposed Pad
Surface Mount YES
Number of Pins 10
Weight 26.109911mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Series Automotive, AEC-Q100
JESD-609 Code e4
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 3 (168 Hours)
Number of Terminations 10
ECCN Code EAR99
Subcategory Switching Regulator or Controllers
Terminal Position DUAL
Terminal Form NO LEAD
Peak Reflow Temperature (Cel) 260
Terminal Pitch 0.5mm
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number TPS63000
Function Step-Up/Step-Down
Number of Outputs 1
Qualification Status Not Qualified
Efficiency 96 %
Output Voltage 5.5V
Output Type Adjustable
Max Output Current 1.2A
Operating Supply Voltage 5.5V
Voltage - Input (Min) 1.8V
Input Voltage-Nom 3.6V
Analog IC - Other Type SWITCHING REGULATOR
Output Configuration Positive
Current - Output 1.6A Switch
Quiescent Current 40μA
Max Output Voltage 5.5V
Voltage - Output (Min/Fixed) 1.2V
Topology Buck-Boost
Control Mode CURRENT-MODE
Frequency - Switching 1.25MHz~1.5MHz
Control Technique PULSE WIDTH MODULATION
Synchronous Rectifier Yes
Min Output Voltage 1.2V
Height 1mm
Length 3mm
Width 3mm
Thickness 900μm
RoHS Status ROHS3 Compliant
Lead Free Lead Free
TPS63000IDRCRQ1 Description

The TPS63000 devices provide a power supply solution for products powered by either a two-cell or three-cell alkaline, NiCd or NiMH battery, or a one-cell Li-Ion or Li-polymer battery. Output currents can go as high as 1200 mA while using a single-cell Li-Ion or Li-Polymer battery, and discharge it down to 2.5 V or lower. The buck-boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using synchronous rectification to obtain maximum efficiency. At low load currents, the converter enters Power Save mode to maintain high efficiency over a wide load current range. The Power Save mode can be disabled, forcing the converter to operate at a fixed switching frequency. The maximum average current in the switches is limited to a typical value of 1800 mA. The output voltage is programmable using an external resistor divider. The converter can be disabled to minimize battery drain. During shutdown, the load is disconnected from the battery. The device is packaged in a 10-pin QFN PowerPAD? package measuring 3 mm × 3 mm (DRC).
TPS63000IDRCRQ1 Features

Qualified for Automotive Applications

Up to 96% Efficiency
1200-mA Output Current at 3.3 V in Step Down Mode (VIN = 3.6 V to 5.5 V)
Automatic Transition between Step Down and Boost Mode
Device Quiescent Current Less Than 50 μA
Input Voltage Range: 1.8 V to 5.5 V
Adjustable Output Voltage From 1.2 V to 5.5 V
Power Save Mode for Improved Efficiency at Low Output Power
Forced Fixed Frequency Operation and Synchronization Possible
Load Disconnect During Shutdown
Over-Temperature Protection
Available in Small 3 mm × 3 mm, QFN-10 Package
TPS63000IDRCRQ1 Applications

All Two-Cell and Three-Cell Alkaline, NiCd or NiMH or Single-Cell Li Battery Powered Products
Portable Audio Players
PDAs
Cellular Phones
Personal Medical Products
White LEDs

Write a review

Note: HTML is not translated!
    Bad           Good