TPS64203DBVRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Weight | 13.409324mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.95mm |
| Base Part Number | TPS64203 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 6.5V |
| Output Type | Transistor Driver |
| Max Output Current | 3A |
| Operating Supply Voltage | 6.5V |
| Input Voltage-Nom | 3.8V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive or Negative |
| Output Current | 3A |
| Voltage - Supply (Vcc/Vdd) | 1.8V~6.5V |
| Quiescent Current | 20μA |
| Control Features | Enable |
| Max Output Voltage | 6.5V |
| Topology | Buck |
| Min Input Voltage | 1.8V |
| Control Mode | CURRENT-MODE |
| Max Input Voltage | 6.5V |
| Synchronous Rectifier | No |
| Min Output Voltage | 1.2V |
| Switcher Configuration | SINGLE |
| Switching Frequency-Max | 800kHz |
| Duty Cycle (Max) | 100% |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS64203DBVRG4 Overview
In the SOT-23-6 package, the switching controller meets most application requirements. dc motor controller is suitable for 1 output generation. Tape & Reel (TR) is the solid enclosure in which PMIC is packaged. With Transistor Driver dc switching's output (s), it is able to handle it. 1.8V~6.5V is the operating voltage and supply voltage of the dc control. Qualified to work in an dc switcher with -40°C~85°C TA. The Surface Mount value makes it suitable for general dc dc regulator. Enable provides dcdc regulator efficient switching control. SWITCHING CONTROLLER analog IC connects the switch converters. There are a DUAL terminal on the switching converters. The 6 terminations can be used for a wide range of dc switching. It is inputted with a DC switcher's voltage of 3.8V. TPS64203 can be used to locate other relevant dc to dc converter ics. 6 pins are present on switching converter. DC regulator outputs 6.5V voltage according to the test statistics. If you are starting a new project, you should note the dc dc regulator's typical output current is 3A. For safe and reliable operation in a circuit, voltage regulator dc to dc is suggested that users apply 6.5V. A dc switching in a dormant state uses 20μA. Because the dc switcher's maximum input voltage is 6.5V users must limit the voltage accordingly. Voltage 1.8V is needed for the supply. A dc switcher can only produce an output current of 3A. A datasheet states that the switching converter can output 6.5V volts at its maximum. 1.2V voltage output is lower than 1.2V. The maximum frequency of this controller is 800kHz.
TPS64203DBVRG4 Features
Transistor Driver Outputs
Enable
TPS64203DBVRG4 Applications
There are a lot of Texas Instruments TPS64203DBVRG4 DC to DC converter applications.
- Energy management systems
- Laboratories
- Smoke prevention equipment
- Refrigerators of central air conditioners
- Computer application technology
- Servo drive system
- Automatic testing equipment
- Program control systems
- Product burn-in
- Radio equipment
