TS12A44515PWR

75ns, 45ns SPST - NC 10Ohm DUAL Analog Switches BREAK-BEFORE-MAKE TS12A44515 14 Pins 1nA 3V 14-TSSOP (0.173, 4.40mm Width)

Manufacturer: Texas Instruments
Nocochips NO: 815-TS12A44515PWR
Package: 14-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 561
Description: 75ns, 45ns SPST - NC 10Ohm DUAL Analog Switches BREAK-BEFORE-MAKE TS12A44515 14 Pins 1nA 3V 14-TSSOP (0.173, 4.40mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Height	1.2mm
Length	5mm
Width	4.4mm
Thickness	1mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free
Factory Lead Time	1 Week
Lifecycle Status	ACTIVE (Last Updated: 5 days ago)
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	14-TSSOP (0.173, 4.40mm Width)
Number of Pins	14
Weight	57.209338mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e4
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	14
ECCN Code	EAR99
Resistance	20Ohm
Terminal Finish	Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory	Multiplexer or Switches
Max Power Dissipation	880mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	3V
Base Part Number	TS12A44515
Output	SEPARATE OUTPUT
Pin Count	14
Number of Channels	4
Max Supply Voltage	12V
Min Supply Voltage	2V
Operating Supply Current	50nA
Power Dissipation	880mW
Max Supply Current	50nA
Throw Configuration	SPST
Turn On Delay Time	120 ns
Number of Inputs	4
Supply Type	Single
Bandwidth	530MHz
Turn-Off Delay Time	80 ns
On-State Resistance (Max)	10Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	94 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	8pF 8pF
On-state Resistance Match-Nom	3.5Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	75ns, 45ns
Charge Injection	-10.5pC
Channel-to-Channel Matching (ΔRon)	2.5 Ω (Max)
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	175ns
Voltage - Supply, Single (V+)	2.7V~12V
Normal Position	NC

TS12A44515PWR Overview

Shipping overseas is convenient with the electronic component packed in 14-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature extended to -40°C~85°C TA. 14 terminations have been made so far. A electrical component with 4 channels is capable of high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. It is injected into the electrical part body with 14 pins. The analog switch ics are built using SPST - NC switching circuits. Try searching for TS12A44515 variants of the analog switch ic. A 20Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 14 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 12V volts for the multiplexer. The digital multiplexer has a low cost Single supply. 2V should be the lowest voltage fed to the electronic component. An operating current of 50nA would be sufficient for this switch device. Analogue multiplexers require a 2.7V~12V voltage to drain from a single voltage supply. If you put voltage higher than 50nA on the digital multiplexer, damage may occur. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. In order to operate the 4 inputs, there are several steps to follow. There are various bandwidths available for data transfer.