Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 4 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Number of Pins |
8 |
Weight |
75.891673mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
15Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
471mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3.3V |
Base Part Number |
TS12A4514 |
Output |
SEPARATE OUTPUT |
Pin Count |
8 |
Number of Channels |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
50nA |
Power Dissipation |
471mW |
Max Supply Current |
50nA |
Throw Configuration |
SPST |
Turn On Delay Time |
120 ns |
Number of Inputs |
1 |
Supply Type |
Single |
Bandwidth |
520MHz |
Turn-Off Delay Time |
80 ns |
On-State Resistance (Max) |
10Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
94 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
7.5pF 7.5pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
75ns, 45ns |
Charge Injection |
-11.5pC |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
2.7V~12V |
Normal Position |
NO |
Height |
1.75mm |
Length |
4.9mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TS12A4514DR Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. A total of 8 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. With a 3.3V voltage supply, the electrical component should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with TS12A4514. Internally, this switch multiplexer has a resistance of 15Ohm. You can find the functions of the 8 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users shouldn't supply more than 12V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. A low voltage of 2V should be applied to the electronic component. For this digital switch to work, 50nA current would suffice. This analog switch requires a voltage of 2.7V~12V to drain from a single voltage supply. If you put voltage higher than 50nA on the digital multiplexer, damage may occur. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. There are 1 inputs to be operated. A 520MHz-bandwidth can be used for data transfer.
TS12A4514DR Features
1 Channels
Switch Circuit: SPST - NO
50nA Supply Current
Bandwidth: 520MHz
TS12A4514DR Applications
There are a lot of Texas Instruments TS12A4514DR Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- CSU
- SONET/SDH ADM
- Cell phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Sample-and-hold systems
- RGB switches
- Battery Powered Systems
- USB 1.1 signal switching circuits
- Video switching