TS12A4515P
| Parameters | |
|---|---|
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 440.409842mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TS12A4515 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 50nA |
| Power Dissipation | 727mW |
| Max Supply Current | 50nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 120 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 520MHz |
| Turn-Off Delay Time | 80 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 94 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF 7.5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 75ns, 45ns |
| Charge Injection | -11.5pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NC |
| Height | 5.08mm |
| Length | 9.81mm |
TS12A4515P Overview
Presented in 8-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. This analog switch is mounted in Through Hole. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -40°C~85°C TA. In total, 8 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 3.3V volts, the electrical part can be powered up and run. As part of its design, the 8 series is equipped with this electronic component. These analog multiplexers are built based on SPST - NC switching circuits. Try searching with TS12A4515 if you're looking for variants. It has an internal resistance of 20Ohm. For details about the functions of 8 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. The digital multiplexer has a low cost Single supply. It is recommended to use 2V as the lowest voltage for the electrical part. For this digital switch to work, 50nA current would suffice. Using only a single voltage supply, this analog switch requires 2.7V~12V voltage. If put voltage greater than 50nA on the device, damage may be caused to the analogue multiplexer. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It is possible to operate 1 inputs. In 520MHz-bandwidths, data can be transferred.
TS12A4515P Features
1 Channels
Switch Circuit: SPST - NC
50nA Supply Current
Bandwidth: 520MHz
TS12A4515P Applications
There are a lot of Texas Instruments TS12A4515P Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Multi-Line E1 Interface Cards
- Data switching
- Precision instrumentation
- Avionics
- T1/E1 Terminals
- Relay Replacement
- Battery-powered systems
- Microwave transmission systems
- PCMCIA cards
