TS1851IDT
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS1851 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 162μA |
| Nominal Supply Current | 170μA |
| Output Current | 46mA |
| Slew Rate | 0.25V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 16nA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 48mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 630kHz |
| Unity Gain BW-Nom | 600 kHz |
| Voltage Gain | 97dB |
| Average Bias Current-Max (IIB) | 0.055μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.063μA |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
TS1851IDT Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used for delivering the op amp. In recent months, the number of terminations has approached 8. Linear amplifier has a total of 8 pins. Please take in mind that this instrumentation amplifier should be run at 3V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 8 pins. The input offset voltage is 3mV. Surface Mount is the recommended mounting type for this linear amplifier. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . An 162μA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 97dB for the time being. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. It is possible to count 1 elements on this buffer amplifier. TAPE AND REEL is adopted to pack the instrumentation amplifier.
TS1851IDT Features
8 Pins
supply voltage of 3V
97dB voltage gain
Output Type: Rail-to-Rail
TS1851IDT Applications
There are a lot of STMicroelectronics TS1851IDT Instrumentational OP Amps applications.
- Hand-held batteries
- Signal amplification
- Industrial applications including automation
- Proportional operation circuits
- Gaming industry
- Oscilloscopes
- Logarithmic operation circuits
- Voltage regulation circuit
- High input resistance broadband
- Micro signal measurement
