TS1854IDT
| Parameters | |
|---|---|
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS1854 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 1.8/5V |
| Operating Supply Current | 162μA |
| Nominal Supply Current | 170μA |
| Output Current | 46mA |
| Slew Rate | 0.25V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 16nA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Output Current per Channel | 48mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 630kHz |
| Unity Gain BW-Nom | 600 kHz |
| Voltage Gain | 97dB |
| Average Bias Current-Max (IIB) | 0.055μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.063μA |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
TS1854IDT Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. There have been a total of 14 terminations over the past year. Linear amplifier has a total of 14 pins. Please take in mind that op amp should be run at 3V. Instrumentation amplifier is a part of Operational Amplifier. An 14-pin op amp ic is included in the package. In terms of the input offset voltage, instrumentation amplifier rates at 3mV. This electronic part is recommended for mounting type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . This op amp can operate from a supply current at 162μA. 97dB should remain the voltage gain. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 4. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted.
TS1854IDT Features
14 Pins
supply voltage of 3V
97dB voltage gain
Output Type: Rail-to-Rail
TS1854IDT Applications
There are a lot of STMicroelectronics TS1854IDT Instrumentational OP Amps applications.
- Television
- Micro signal measurement
- Band-stop filter
- Vehicle electronics
- Thermocouples
- RF cable systems
- Radiation thermometry transducers
- Computer workstations
- Proportional counter tubes
- Blood pressure sensors
