TS272CDT
| Parameters | |
|---|---|
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 3.5MHz |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 83.52dB |
| Average Bias Current-Max (IIB) | 0.00015μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Power | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 10V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS272 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Power Supplies | 10V |
| Number of Channels | 2 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 3mA |
| Output Current | 60mA |
| Slew Rate | 5.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
TS272CDT Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. An op amp ic of the General Purpose type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. The number of terminations approaches 8. The pins on this board total to 8 in total. It is important to remember that this op amp should be operated at a voltage of 10V volts. This particular linear amplifier is a type of Operational Amplifier device, to be precise. An 8-pin op amp ic is included in the package. There is an input offset voltage of 10mV for this buffer op amp. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureThis op amp can operate from a supply current at 1mA. The voltage gain should stay at 83.52dB. Op amp ic has 2 channels. The operating supply voltage of the buffer op amp is rated at 8V. TAPE AND REEL is adopted to pack the instrumentation amplifier.
TS272CDT Features
8 Pins
supply voltage of 10V
83.52dB voltage gain
TS272CDT Applications
There are a lot of STMicroelectronics TS272CDT Instrumentational OP Amps applications.
- PDA
- earphone
- MP3
- Active probe
- High/low-pass filter circuit
- Large motor controllers
- Automation control systems
- Medical instruments
- Home audio systems
- Signal operation
