TS272CN
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 10V |
| Base Part Number | TS272 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Power Supplies | 10V |
| Number of Channels | 2 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 3mA |
| Output Current | 60mA |
| Slew Rate | 5.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 3.5MHz |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 83.52dB |
| Average Bias Current-Max (IIB) | 0.00015μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Power | NO |
| Height | 3.32mm |
| Length | 10.92mm |
| Width | 6.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS272CN Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. This is a General Purpose type op amp. Instrumentation amplifier is delivered in a Tube case. It is estimated that there will be at least 8 terminations this year. The pins on this board total to 8 in total. I would like to remind you that this buffer op amp should be powered by an 10V battery. It should be noted that this op amp is a type of Operational Amplifier device. The buffer op amp includes 8 pins. With regard to input offset voltage, instrumentation amplifier is rated at 10mV. For this electrical component, Through Hole is the recommended mounting type. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. Using an 1mA supply current, this operational amplifier ics can be operated. Keeping the voltage gain at 83.52dB is the best course of action. Instrumentation amplifier has 2 channels on it. The operating supply voltage of the buffer op amp is rated at 8V.
TS272CN Features
8 Pins
supply voltage of 10V
83.52dB voltage gain
TS272CN Applications
There are a lot of STMicroelectronics TS272CN Instrumentational OP Amps applications.
- Ultrasound transducers
- Radar
- Strain gauges
- Industrial control system
- Division circuits
- Instrumentation
- Inverse/same-phase proportional circuit
- Oscilloscopes
- Automatic control
- High gain DC amplifier
