TS272IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 10V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS272 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Power Supplies | 10V |
| Number of Channels | 2 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 3mA |
| Output Current | 60mA |
| Slew Rate | 5.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 3.5MHz |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 83.52dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Power | NO |
| Height | 1.65mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS272IDT Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. An op amp ic of the General Purpose type. In the case of Cut Tape (CT) cases, linear amplifier will be delivered. We are approaching the 8h termination of the year. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 10V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. It has 8 pins that make up the linear amplifier. Regarding input offset voltage, buffer amplifier rates 10mV voltage. It is recommended that this electronic component be mounted using the Surface Mount mounting type. With regard to operating temperature, this op amp functions well at -40°C~125°C. Operational amplifier can operate supply current at 1mA. You should keep the voltage gain at 83.52dB for the time being. Buffer op amp is equipped with 2 channels on the device. The operating supply voltage of instrumentation amplifier is rated 8V voltage. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
TS272IDT Features
8 Pins
supply voltage of 10V
83.52dB voltage gain
TS272IDT Applications
There are a lot of STMicroelectronics TS272IDT Instrumentational OP Amps applications.
- Proportional counter tubes
- High-frequency data acquisition systems
- Addition operation circuits
- Non-polarized electrodes
- Strain gauges
- Portable media players
- Medical imaging
- Automatic control
- Micro signal measurement
- Laptop
