banner_page

TS274ACDT

45mA per Channel 1pA 65 dB Instrumentational OP Amps 0.00015μA 8V 3V~16V ±1.5V~8V TS274 14 Pins 14-SOIC (0.154, 3.90mm Width)


  • Manufacturer: STMicroelectronics
  • Nocochips NO: 761-TS274ACDT
  • Package: 14-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 641
  • Description: 45mA per Channel 1pA 65 dB Instrumentational OP Amps 0.00015μA 8V 3V~16V ±1.5V~8V TS274 14 Pins 14-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 6 months ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 14-SOIC (0.154, 3.90mm Width)
Number of Pins 14
Operating Temperature 0°C~70°C
Packaging Tape & Reel (TR)
JESD-609 Code e4
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Operational Amplifier
Packing Method TAPE AND REEL
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 10V
Terminal Pitch 1.27mm
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number TS274
Pin Count 14
Operating Supply Voltage 8V
Number of Elements 4
Power Supplies 3/16V
Operating Supply Current 1mA
Nominal Supply Current 6mA
Output Current 60mA
Slew Rate 5.5V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 65 dB
Current - Input Bias 1pA
Voltage - Supply, Single/Dual (±) 3V~16V ±1.5V~8V
Output Current per Channel 45mA
Input Offset Voltage (Vos) 5mV
Gain Bandwidth Product 3.5MHz
Unity Gain BW-Nom 3500 kHz
Voltage Gain 83.52dB
Average Bias Current-Max (IIB) 0.00015μA
Low-Offset NO
Frequency Compensation YES
Voltage - Input Offset 900μV
Low-Bias YES
Height Seated (Max) 1.75mm
Length 8.65mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

TS274ACDT Overview


Op amp is packaged in 14-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the General Purpose-type. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be 14 terminations in the next few months. The pins on this board total to 14 in total. It would be helpful if you could remember that this op amp ic should be powered by an 10V battery. It should be noted that this op amp is a type of Operational Amplifier device. There are 14 pins on this chip. With regards to the offset voltage of the input, buffer amplifier is rated at 5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, this op amp functions well at 0°C~70°C. It is possible to operate this buffer amplifier from a supply current of 1mA . You should keep the voltage gain at 83.52dB for the time being. The linear amplifier consists of 4 different elements in total. The operating supply voltage of the buffer op amp is rated at 8V. This linear amplifier pack is based on the TAPE AND REEL axis.

TS274ACDT Features


14 Pins
supply voltage of 10V
83.52dB voltage gain

TS274ACDT Applications


There are a lot of STMicroelectronics TS274ACDT Instrumentational OP Amps applications.

  • Exponential operation circuits
  • Professional videography
  • Instrumentation
  • Ultrasound transducers
  • Micro signal measurement
  • Power transmission
  • Band-stop filter
  • Signal transformation
  • Test and measurement instruments
  • Blood pressure sensors

Write a review

Note: HTML is not translated!
    Bad           Good