TS274IDT
| Parameters | |
|---|---|
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 10V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS274 |
| Pin Count | 14 |
| Operating Supply Voltage | 8V |
| Number of Elements | 4 |
| Power Supplies | 3/16V |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 6mA |
| Output Current | 60mA |
| Slew Rate | 5.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Gain Bandwidth Product | 3.5MHz |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 83.52dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
TS274IDT Overview
Op amp is packaged in 14-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. A total of 14 terminations have been reported in the past few weeks. A total of 14 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 10V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. There are 14 pins on this chip. Op amp rates 10mV as input offset voltage. This electronic part is best mounted with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. The buffer amplifier is capable of operating from a supply current of 1mA . 83.52dB should be the voltage gain. It is possible to count 4 elements on this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 8V. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
TS274IDT Features
14 Pins
supply voltage of 10V
83.52dB voltage gain
TS274IDT Applications
There are a lot of STMicroelectronics TS274IDT Instrumentational OP Amps applications.
- Video amplifiers
- High speed sample
- Power generator
- Navigation
- Home audio systems
- High input resistance broadband
- Portable docking station
- Division circuits
- Fission chambers
- Band-pass filter
