TS27L2CDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 10V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS27L2 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Power Supplies | 5/10V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 30μA |
| Output Current | 60mA |
| Slew Rate | 0.04V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.00015μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS27L2CDT Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. There are two types of operational amplifiers in this circuit. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. The total number of pins on linear amplifier is 8. It is important to remember that this op amp should be operated at a voltage of 10V volts. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are included on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 10mV. For this electronic part, it is recommended that you mount it with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . This op amp can operate from a supply current at 10μA. Voltage gain should remain at 100dB. 2 elements make up the design of this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 8V voltage. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
TS27L2CDT Features
8 Pins
supply voltage of 10V
100dB voltage gain
TS27L2CDT Applications
There are a lot of STMicroelectronics TS27L2CDT Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Oscilloscopes
- Biopotential
- High gain DC amplifier
- PDA
- Video data acquisition
- Addition operation circuits
- Differentiator circuits
- Home audio systems
- Band-pass filter
