TS27L2IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 10V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS27L2 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Power Supplies | 5/10V |
| Number of Channels | 2 |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 30μA |
| Output Current | 60mA |
| Slew Rate | 0.04V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Height | 1.65mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
TS27L2IDT Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. This is a General Purpose type op amp. A Cut Tape (CT) case is used for delivering the op amp. The number of terminations is approaching the 8 mark. Buffer amplifier has a total of 8 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 10V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are included on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 10mV. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Using an 10μA supply current, this operational amplifier ics can be operated. 100dB should be the voltage gain. There are a total of 2 channels available on the op amps. The operating supply voltage of the buffer op amp is rated at 8V. As a result of this, the buffer amplifier is packed in TAPE AND REEL.
TS27L2IDT Features
8 Pins
supply voltage of 10V
100dB voltage gain
TS27L2IDT Applications
There are a lot of STMicroelectronics TS27L2IDT Instrumentational OP Amps applications.
- High-frequency data acquisition systems
- Ultrasound transducers
- Automotive sensors
- Professional videography
- Radiation thermometry transducers
- Large motor controllers
- Exponential operation circuits
- Portable docking station
- High/low-pass filter circuit
- Test and measurement instruments
