TS27L4IDT
| Parameters | |
|---|---|
| Power Supplies | 10V |
| Number of Channels | 4 |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 10μA |
| Output Current | 60mA |
| Slew Rate | 0.04V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 1.1mV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Ambient Temperature Range High | 125°C |
| Height | 1.75mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 10V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS27L4 |
| Pin Count | 14 |
| Operating Supply Voltage | 8V |
TS27L4IDT Overview
There is a 14-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. Op amps are General Purpose types of amplifier on the chip. Upon delivery, op amp ic is packaged in a Cut Tape (CT) case. It is estimated that there will be 14 terminations in the next few months. There are a total of 14 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 10V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. It has 14 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 1.1mV. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 10μA . Maintain 100dB as the voltage gain. Buffer op amp is equipped with 4 channels on the device. The operating supply voltage of the buffer op amp is rated at 8V. TAPE AND REEL is adopted to pack the instrumentation amplifier.
TS27L4IDT Features
14 Pins
supply voltage of 10V
100dB voltage gain
TS27L4IDT Applications
There are a lot of STMicroelectronics TS27L4IDT Instrumentational OP Amps applications.
- Micro signal measurement
- Digital cameras
- Proportional operation circuits
- Instrumentation
- Power control
- E-book readers
- High gain DC amplifier
- Thermocouples
- Blood pressure sensors
- Commercial audio systems
