TS27M2IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 10V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS27M2 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 8V |
| Power Supplies | 5/10V |
| Number of Channels | 2 |
| Operating Supply Current | 150μA |
| Nominal Supply Current | 400μA |
| Output Current | 45mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 93.98dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS27M2IDT Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Cut Tape (CT) case. We are approaching the 8h termination of the year. The total number of pins on linear amplifier is 8. Please take in mind that this instrumentation amplifier should be run at 10V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 8-pin op amp ic is included in the package. Op amp ic rates 10mV for input offset voltage. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureOperational amplifier can operate supply current at 150μA. Keeping the voltage gain at 93.98dB is the best course of action. Buffer op amp is equipped with 2 channels on the device. The operating supply voltage of instrumentation amplifier is rated 8V voltage. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted.
TS27M2IDT Features
8 Pins
supply voltage of 10V
93.98dB voltage gain
TS27M2IDT Applications
There are a lot of STMicroelectronics TS27M2IDT Instrumentational OP Amps applications.
- Professional videography
- Division circuits
- Video amplifiers
- Television broadcasting equipment
- Oscilloscopes
- Automotive sensors
- Polarized electrodes
- Measurements of Wheatstone bridge
- Logarithmic operation circuits
- Proportional operation circuits
