TS27M4CDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 10V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS27M4 |
| Pin Count | 14 |
| Operating Supply Voltage | 8V |
| Power Supplies | 10V |
| Number of Channels | 4 |
| Operating Supply Current | 150μA |
| Nominal Supply Current | 800μA |
| Output Current | 45mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 93.98dB |
| Average Bias Current-Max (IIB) | 0.00015μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | YES |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS27M4CDT Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. Op amps are General Purpose types of amplifier on the chip. The op amp is delivered to you in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 14. The total number of pins on linear amplifier is 14. It is important to remember that this op amp should be operated at a voltage of 10V volts. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 14 pins. As far as the input offset voltage is concerned, linear amplifier rates at 10mV. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. This op amp can operate from a supply current at 150μA. It is a member of the 93.98dB's 93.98dB family. On the buffer amps, there are 4 channels that can be used. The operating supply voltage of the buffer op amp is rated at 8V. The instrumentation amplifier is packed in the form of TAPE AND REEL.
TS27M4CDT Features
14 Pins
supply voltage of 10V
93.98dB voltage gain
TS27M4CDT Applications
There are a lot of STMicroelectronics TS27M4CDT Instrumentational OP Amps applications.
- Differentiator circuits
- earphone
- Broadcasting
- Comparator
- Inverse/same-phase proportional circuit
- Communication device
- Medical instruments
- Instrumentation
- Hand-held batteries
- Radar
