TS2DDR2811ZXYR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-UFBGA |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 6Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Frequency | 10GHz |
| Base Part Number | TS2DDR2811 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Number of Channels | 8 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 250μA |
| Nominal Supply Current | 250μA |
| Max Supply Current | 500μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| Bandwidth | 1.1 GHz |
| On-State Resistance (Max) | 6Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Channel Capacitance (CS(off), CD(off)) | 2.5pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -37dB @ 200MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 15ns |
| Switch-off Time-Max | 9ns |
| Voltage - Supply, Single (V+) | 3V~3.6V |
| Normal Position | NC |
| Height | 610μm |
| Length | 2.5mm |
| Width | 3mm |
| Thickness | 360μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS2DDR2811ZXYR Overview
Shipping overseas is convenient with the electronic component packed in 20-UFBGA. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, 20 terminations have occurred. This electronic part offers high-quality output due to its 8 channels. If the voltage supply is 3.3V volts, the electrical component should be turned on and run. An electrical component like this is included in the 20 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with TS2DDR2811 to find analog multiplexer variants. An switch multiplexer with 6Ohm internal resistance has a value of 6Ohm. To find out what the 20 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 3.6V to a switch device. An effective Single supply digital multiplexer. It is recommended to use 3V as the lowest voltage for the electrical part. This multiplexer would work with 250μA current. The voltage required by this switch device is 3V~3.6V, draining from a single voltage supply. Put voltage above 500μA on the multiplexer to cause damage. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. There are various bandwidths available for data transfer.
TS2DDR2811ZXYR Features
8 Channels
Switch Circuit: SPST - NO
250μA Supply Current
Bandwidth: 1.1 GHz
TS2DDR2811ZXYR Applications
There are a lot of Texas Instruments TS2DDR2811ZXYR Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- High-Voltage
- Communications systems
- HDTV
- Cell phones
- Imaging
- Channel Banks
- CSU
- Medical Instrumentation
- RGB switches
