TS3A24157RSERG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Weight | 7.002332mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 600mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TS3A24157 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Power Supplies | 1.8/3V |
| Number of Channels | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 15nA |
| Nominal Supply Current | 15nA |
| Max Supply Current | 200nA |
| Turn On Delay Time | 40 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Bandwidth | 50MHz |
| Turn-Off Delay Time | 30 ns |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 50nA |
| Channel Capacitance (CS(off), CD(off)) | 50pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 35ns, 25ns |
| Charge Injection | 8.75pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 80ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Signal Current-Max | 0.1A |
| Height | 600μm |
| Length | 1.5mm |
| Width | 2mm |
| Thickness | 550μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS3A24157RSERG4 Overview
Due to its 10-UFQFN packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. 10 terminations have been made so far. The electronic part delivers high-quality output through its 2 channels. Powered by a 1.8V voltage supply, the electrical part should be switched on and run. As part of the design of the 10 series, this electronic part has been incorporated into the system. These analog multiplexers are built based on SPDT switching circuits. Try searching with TS3A24157 to find analog multiplexer variants. It has an internal resistance of 600mOhm. Please refer to the datasheets for 10 pins functions. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 3.6V. The digital multiplexer has a low cost Single supply. 1.65V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 15nA. An analogue multiplexer drains from a single voltage supply at 1.65V~3.6V. If you put voltage higher than 200nA on the digital multiplexer, damage may occur. There are 2 inputs to be operated. There are various bandwidths available for data transfer. Multiplexer ics with 4 outputs are available.
TS3A24157RSERG4 Features
2 Channels
Switch Circuit: SPDT
15nA Supply Current
Bandwidth: 50MHz
TS3A24157RSERG4 Applications
There are a lot of Texas Instruments TS3A24157RSERG4 Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- Medical systems
- Audio and video switching
- RGB switches
- Audio signal routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fiber to the Home
- PDH Multiplexers
- PDAs
- Automotive applications
