TS3A24159DRCRG4

35ns, 25ns SPDT 300mOhm DUAL Analog Switches BREAK-BEFORE-MAKE TS3A24159 10 Pins 10nA 1.8V 10-VFDFN Exposed Pad

Manufacturer: Texas Instruments
Nocochips NO: 815-TS3A24159DRCRG4
Package: 10-VFDFN Exposed Pad
Datasheet: PDF
Stock: 960
Description: 35ns, 25ns SPDT 300mOhm DUAL Analog Switches BREAK-BEFORE-MAKE TS3A24159 10 Pins 10nA 1.8V 10-VFDFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	ACTIVE (Last Updated: 3 days ago)
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-VFDFN Exposed Pad
Number of Pins	10
Weight	26.109911mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e4
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	2 (1 Year)
Number of Terminations	10
Resistance	300mOhm
Terminal Finish	Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory	Multiplexer or Switches
Terminal Position	DUAL
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	1.8V
Terminal Pitch	0.5mm
Base Part Number	TS3A24159
Output	SEPARATE OUTPUT
Pin Count	10
Power Supplies	1.8/3V
Number of Channels	2
Number of Circuits	2
Max Supply Voltage	3.6V
Min Supply Voltage	1.65V
Operating Supply Current	15nA
Nominal Supply Current	15nA
Max Supply Current	100nA
Turn On Delay Time	40 ns
Supply Type	Single
Bandwidth	23MHz
Turn-Off Delay Time	30 ns
On-State Resistance (Max)	300mOhm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	73 dB
Current - Leakage (IS(off)) (Max)	10nA
Channel Capacitance (CS(off), CD(off))	90pF
On-state Resistance Match-Nom	0.02Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	35ns, 25ns
Charge Injection	9pC
Channel-to-Channel Matching (ΔRon)	10m Ω
Crosstalk	-96dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	75ns
Switch-off Time-Max	35ns
Voltage - Supply, Single (V+)	1.65V~3.6V
Signal Current-Max	0.1A
Height	1mm
Length	3mm
Width	3mm
Thickness	900μm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

TS3A24159DRCRG4 Overview

Shipping overseas is convenient due to the electrical component's packing in 10-VFDFN Exposed Pad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 10. Due to its 2 channels, the electrical component produces high-quality output. When a voltage supply of 1.8V is used, the electronic component should be turned on and run. There is an electrical component included in the 10 series. A SPDT switching circuit is used to build these analog multiplexers. It consists of 2 circuits. Try searching for the analog switch ic with TS3A24159 if you are looking for variants. In this multiplexer, the internal resistance is 300mOhm. You can find the functions of the 10 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 3.6V volts for the multiplexer. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 1.65V. An operating current of 15nA would be sufficient for this switch device. The voltage required by this switch device is 1.65V~3.6V, draining from a single voltage supply. If put voltage greater than 100nA on the device, damage may be caused to the analogue multiplexer. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. In 23MHz-bandwidths, data can be transferred.