TS3A44159RSVRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-UFQFN |
| Number of Pins | 16 |
| Weight | 40.908362mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 450mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Base Part Number | TS3A44159 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Number of Channels | 4 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 15nA |
| Nominal Supply Current | 150nA |
| Max Supply Current | 400nA |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Bandwidth | 35MHz |
| Turn-Off Delay Time | 45 ns |
| On-State Resistance (Max) | 450mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 50pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 23ns, 32ns |
| Charge Injection | 139pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -73dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height | 550μm |
| Length | 2.6mm |
| Width | 1.8mm |
| Thickness | 500μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS3A44159RSVRG4 Overview
The electrical component comes in 16-UFQFN packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 16. A electrical component with 4 channels is capable of high-quality output. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. It is part of the design of the 16 series that this electronic component is included. A SPDT switching circuit is used to build these analog multiplexers. Try searching for the analog switch ic with TS3A44159 if you are looking for variants. Analog switches have 450mOhm internal resistance. Datasheets for 16 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 4.3V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. 1.65V should be the lowest voltage fed to the electronic component. The switch device would be able to operate with 15nA current. This analogue multiplexer requires a voltage of 1.65V~4.3V when it drains from a single voltage supply. If put voltage greater than 400nA on the device, damage may be caused to the analogue multiplexer. Among the inputs that can be operated are the 4 inputs. There are 35MHz bandwidths for data transfer. The analog switch ics has 8 outputs.
TS3A44159RSVRG4 Features
4 Channels
Switch Circuit: SPDT
15nA Supply Current
Bandwidth: 35MHz
TS3A44159RSVRG4 Applications
There are a lot of Texas Instruments TS3A44159RSVRG4 Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Public switching systems
- SDH/SONET multiplexers
- Fiber In The Loop (FITL)
- Access Concentrators
- E1 Network Equipment
- Intelligent PBX
- Medical systems
- Relay Replacement
- Microprocessor Controlled Analog Systems
