TS3A4742DCNR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 700mOhm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TS3A4742 |
| Pin Count | 8 |
| Operating Supply Voltage | 3V |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Nominal Supply Current | 75nA |
| Max Supply Current | 750nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 15 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Bandwidth | 125MHz |
| Turn-Off Delay Time | 10 ns |
| On-State Resistance (Max) | 900mOhm |
| High Level Output Current | 100mA |
| Low Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 23pF 20pF |
| On-state Resistance Match-Nom | 0.09Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 14ns, 9ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Normal Position | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.63mm |
| Thickness | 1.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS3A4742DCNR Overview
Packed in SOT-23-8, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 8. This electronic part offers high-quality output due to its 2 channels. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. There are 8 pins injected into the electronic part body. A SPST - NC switching circuit is used to build these analog multiplexers. Use TS3A4742 to search for variants of the digital switches. A 700mOhm internal resistance characterizes this multiplexer. Please refer to the datasheets for 8 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 3.6V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. A voltage of 1.6V~3.6V is required for this switch device, which drains from a single voltage source. When the digital multiplexer is charged above 750nA, damage can occur. Operating voltages range from 3V. In order to operate the 2 inputs, there are several steps to follow. The data can be transferred over a wide range of bandwidths, called 125MHz bandwidths.
TS3A4742DCNR Features
2 Channels
Switch Circuit: SPST - NC
Bandwidth: 125MHz
TS3A4742DCNR Applications
There are a lot of Texas Instruments TS3A4742DCNR Analog Switches & Multiplexers ICs applications.
- Medical systems
- FTTH
- New designs requiring multiplexer functions
- SDH
- Fiber In The Loop (FITL)
- Audio/video switches
- Multiplexers
- Modems
- Medical
- Access Concentrators
