Parameters |
Nominal Supply Current |
2.5μA |
Max Supply Current |
7μA |
Turn On Delay Time |
9.5 ns |
Supply Type |
Single |
Bandwidth |
300MHz |
Turn-Off Delay Time |
7.5 ns |
On-State Resistance (Max) |
10Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
48 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
4.5pF 9pF |
On-state Resistance Match-Nom |
0.4Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
8ns, 6.5ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-48dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
10.5ns |
Switch-off Time-Max |
9ns |
Voltage - Supply, Single (V+) |
1.65V~3.6V |
Drain to Source Resistance |
7Ohm |
Normal Position |
NC |
Signal Current-Max |
0.1A |
Height |
1.75mm |
Length |
4.9mm |
Width |
3.9mm |
Thickness |
1.5mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
74.502547mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
16 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
10Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
2.5V |
Base Part Number |
TS3A5018 |
Pin Count |
16 |
Number of Outputs |
8 |
Operating Supply Voltage |
3V |
Number of Channels |
4 |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
2.3V |
Operating Supply Current |
2.5μA |
TS3A5018DBQR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SSOP (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. By its 4 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 2.5V voltage supply. A total of 16 pins are injected into the electrical part body. SPDT switching circuits are used in these analog switch ics. Try searching for the analog switch ic with TS3A5018 if you are looking for variants. There is 10Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 3.6V should not normally be supplied to the switches. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 2.3V. This digital switch can be operated with a current of 2.5μA. The voltage required by this switch device is 1.65V~3.6V, draining from a single voltage supply. If put voltage greater than 7μA on the device, damage may be caused to the analogue multiplexer. Operating voltages range from 3V. The data can be transferred over a wide range of bandwidths, called 300MHz bandwidths. There is 7Ohm resistance between Drain and Source for this electronic part. The analog switch ics has 8 outputs.
TS3A5018DBQR Features
4 Channels
Switch Circuit: SPDT
2.5μA Supply Current
Bandwidth: 300MHz
Drain-to-Source resistance: 7Ohm
TS3A5018DBQR Applications
There are a lot of Texas Instruments TS3A5018DBQR Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Precision test equipment
- Video switching
- Avionics test equipment
- Cellular phones
- Wireless Local Loop
- ATM
- Multi-Line E1 Interface Cards
- Cable PC
- Audio signal routing