Parameters |
Thickness |
900μm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 5 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-VFQFN Exposed Pad |
Number of Pins |
16 |
Weight |
37.194574mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
16 |
Resistance |
10Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
2.5V |
Terminal Pitch |
0.5mm |
Base Part Number |
TS3A5018 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
2.5/3.3V |
Number of Channels |
4 |
Number of Circuits |
4 |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
2.5μA |
Nominal Supply Current |
2.5μA |
Max Supply Current |
7μA |
Turn On Delay Time |
8 ns |
Supply Type |
Single |
Bandwidth |
300MHz |
Turn-Off Delay Time |
6.5 ns |
On-State Resistance (Max) |
10Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
48 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
4.5pF 9pF |
On-state Resistance Match-Nom |
0.4Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
8ns, 6.5ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-48dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
10.5ns |
Switch-off Time-Max |
9ns |
Voltage - Supply, Single (V+) |
1.65V~3.6V |
Signal Current-Max |
0.1A |
Height |
1mm |
Length |
4mm |
Width |
3.5mm |
TS3A5018RGYRG4 Overview
This electronic part is conveniently packaged in 16-VFQFN Exposed Pad, making it easy to ship abroad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. Due to its 4 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 2.5V voltage supply. The electrical component body receives 16 pins. SPDT switching circuits are used in these analog switch ics. A total of 4 circuits make up this switch device. Try searching for the analog switch ic with TS3A5018 if you are looking for variants. This digital multiplexer has 10Ohm internal resistance. Datasheets for 16 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 3.6V volts for the multiplexer. An effective Single supply digital multiplexer. 1.8V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 2.5μA current would be sufficient. An analogue multiplexer drains from a single voltage supply at 1.65V~3.6V. A digital multiplexer may suffer damage if voltage is applied above 7μA. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. There are 300MHz bandwidths for data transfer.
TS3A5018RGYRG4 Features
4 Channels
Switch Circuit: SPDT
2.5μA Supply Current
Bandwidth: 300MHz
TS3A5018RGYRG4 Applications
There are a lot of Texas Instruments TS3A5018RGYRG4 Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- Central office
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Relay replacements
- RGB switches
- Imaging
- DSLAMs
- Precision test equipment
- Battery Powered Systems
- High speed data transmission line cards